Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The TCM and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning reduction requirement, shift position, DTCs and other data. The ECM sends signals to the TCM concerning engine torque, opening angles of the throttle valve, temperature of the engine coolant and other data.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
U0100 Lost Communication with ECM / PCM "A" When TCM cannot receive communication signals from ECM.
(1 trip detection logic)
·

Open or short in TCM and ECM circuit

·

TCM

·

ECM


- Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246497E02
0.646,2.927 1.271,3.333 0.625,0.406 10 TCM 0.76,1.094 1.438,1.469 0.677,0.375 10 CANH 0.781,1.781 1.417,2.135 0.635,0.354 10 CANL 0.646,2.771 0.948,3.01 0.302,0.24 10 E9 6.302,2.75 6.719,3.156 0.417,0.406 10 E3 6.135,1.094 6.927,1.542 0.792,0.448 10 CANH 6.135,1.781 6.844,2.188 0.708,0.406 10 CANL 0.969,2.323 1.427,2.646 0.458,0.323 10 E1 1.25,1 1.698,1.354 0.448,0.354 10 7 1.25,1.698 1.719,2.104 0.469,0.406 10 17 5.917,0.99 6.313,1.323 0.396,0.333 10 4 5.927,1.688 6.396,2 0.469,0.313 10 3 1.25,2.219 1.646,2.552 0.396,0.333 10 4 6.292,2.917 6.927,3.302 0.635,0.385 10 ECM

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the E9 TCM connector.


b.

Disconnect the E3 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
E9-7 (CANH) - E3-4 (CANH) Always Below 1 Ω
E9-17 (CANL) - E3-3 (CANL) Always
E9-7 (CANH) - Body ground Always 1 MΩ or higher
E9-17 (CANL) - Body ground Always



d.

Reconnect the E9 TCM connector.


e.

Reconnect the E3 ECM connector.

Result:
proceed to
OK
NG




OK

2.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>TCM>REMOVAL

Result:
Proceed to
NEXT




NEXT

3.CHECK DTC OUTPUT (DTC U0100)
3.CHECK DTC OUTPUT (DTC U0100)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTC.

Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 565

e.

Turn the ignition switch off.


f.

Turn the tester off.


g.

Start the engine.


h.

Turn the tester on.


i.

Enter the following menus: Powertrain / ECT / DTC / Current or Pending.

Powertrain > ECT > Trouble Codes
50001 565

j.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
U0100(K3-VE) A
U0100(3SZ-VE) B
No DTC C


HINT:

When not using the intelligent tester, refer to DTC CHECK / CLEAR.

Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR




A

B

C

END