The TCM receives engine speed from ECM and this DTC is output when engine speed signals are not input from the ECM to the TCM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P0725 | Engine Speed Input Circuit | When the RENG (ATNE) signal is not input from the ECM to the TCM for a specific period of time.
(2 trip detection logic) |
·
Open or short circuit in wire harness between ECM and TCM ·
TCM ·
SFI system |
Come on | Blinks | DTC stored |
MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.
Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC / Current or pending.
Read the DTCs.
Enter the following menus: Powertrain / ECT / DTC / Current or pending.
Read the DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0725 | A |
| P0725 and other DTCs | B |
If any other DTCs besides P0725 are output, perform troubleshooting for those DTCs first.
When not using the intelligent tester, refer to DTC CHECK / CLEAR in SFI SYSTEM
(K3-VE : Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR)
(3SZ-VE : Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR)
and DTC CHECK / CLEAR in AUTOMATIC TRANSMISSION SYSTEM (See page Drivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
A
B
Disconnect the E9 TCM connector.
Disconnect the E3 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E9-8 (RENG) - E3-24 (ATNE) | Always | Below 1 Ω |
| E3-24 (ATNE) or E9-8 (RENG) - Body ground | Always | 10 kΩ or higher |
Reconnect the E9 TCM connector.
Reconnect the E3 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>TCM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTC.
Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the tester off.
Start the engine.
turn the tester on.
Enter the following menus: Powertrain / ECT / DTC / Current or Pending.
Read the DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0725
3SZ-VE (w/ Rear Heated Oxygen Sensor) |
A |
| P0725
3SZ-VE (w/o Rear Heated Oxygen Sensor) |
B |
| P0725
K3-VE |
C |
| No DTC | D |
When not using the intelligent tester, refer to DTC CHECK / CLEAR.
Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR
A
B
C
Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
D