Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015087 TORQUE CONVERTER AND DRIVE PLATE G

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C151051C02
3.135,2.063 3.323,2.063 false
V100135

Difficult
V100136

Smooth


Press on the splines of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch.

Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
C267383C02
0.135,0.135 0.552,0.552 0.417,0.417 10 *a
*a Sample showing maximum allowable amount of powder in ATF


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF that was removed from a torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly before replacing the ATF.



d.
C011090

Clean and check the oil cooler and oil pipe line.

HINT:
·

If the torque converter assembly is inspected or the ATF is replaced, it is necessary to clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2.0 kgf/ cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.

·

If the ATF is cloudy, inspect the oil cooler.




e.
D025368C03
1.729,1.885 2.208,1.865 true 2.26,1.76 2.813,2.177 0.552,0.417 10 *c 0.49,0.167 1.125,0.625 0.635,0.458 10 *a 1.531,0.167 2.208,0.635 0.677,0.469 10 *b
*a CORRECT
*b INCORRECT
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 2.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
C248821C02
3.146,2.063 3.333,2.063 false
V100144

Measurement Point


Check the drive plate damage.


b.

Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.25 mm (0.0098 in.)


HINT:
·

If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

·

If installing a new drive plate, confirm that the spacers are oriented properly before tightening the bolts (See page for K3-VE: Engine / Hybrid System>K3-VE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>REMOVAL for 3SZ-VE: Engine / Hybrid System>3SZ-VE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>REMOVAL).