Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 3SZ-VE) › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002984 CLUTCH _0015096 CLUTCH UNIT(for 3SZ-VE) A

CLUTCH  CLUTCH UNIT(for 3SZ-VE)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C142544N01
2.752,1.319 2.845,1.613 2.845,1.613 2.962,1.613 false 2.985,1.535 3.289,1.687 0.304,0.151 10 SST

a.

Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

SST
09301-00131  

NOTICE:

Insert the clutch disc assembly in the correct orientation.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C267586C02
1.427,1.771 1.031,1.99 1.031,1.99 1.417,1.906 true 0.958,0.063 1.115,0.26 0.156,0.198 10 7 0.438,0.802 0.594,1 0.156,0.198 10 3 0.635,1.781 0.792,1.979 0.156,0.198 10 6 0.802,1.938 1.115,2.135 0.313,0.198 10 *a 1.917,1.979 2.073,2.177 0.156,0.198 10 2 2.708,1.156 2.865,1.354 0.156,0.198 10 5 2.333,0.083 2.969,0.281 0.635,0.198 10 1 (*b) 4
*a Matchmark
*b Temporarily


a.

Align the matchmarks on the clutch cover assembly and flywheel sub-assembly.


b.

Following the procedures shown in the illustration, tighten the 6 bolts, in order starting with the bolt located near the knock pin on the top.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, uniformly tighten the bolts.

·

Check that the disc is in the center by moving SST vertically and horizontally, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C142545N01
2.838,0.414 3.168,0.584 0.33,0.17 10 SST 2.803,0.492 2.56,0.492 false

a.

Using a dial indicator with roller instrument, check the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.020 in.)



b.

If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support onto the manual transmission assembly.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 31232A 5.INSTALL RELEASE BEARING HUB CLIP

a.

Install the release bearing hub clip to the clutch release fork sub-assembly.


b.

Install the release fork support spring to the clutch release fork sub-assembly.


Hide 31204 6.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

C145212

a.

Apply release hub grease to the clutch release fork sub-assembly and release bearing assembly contact surfaces, release fork and push rod contact surface and release fork pivot point.

Sealant:

Toyota Genuine Release Hub Grease or equivalent



Hide 31230 7.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

C147002

a.

Apply clutch spline grease to the input shaft spline.

Sealant:

Toyota Genuine Clutch Spline Grease or equivalent



b.

Install the clutch release bearing assembly onto the clutch release fork sub-assembly, and then install them onto the manual transmission assembly.

NOTICE:

After the installation, move the fork forward and backward to check that the clutch release bearing assembly slides smoothly.