Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is stored, the skid control ECU (brake actuator assembly) stores the current vehicle (sensor) state as freeze frame data.


b.

The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

HINT:
·

If the vehicle is stopped or at a low speed (7 km/h (4 mph) or less), or if a DTC is stored, the skid control ECU (brake actuator assembly) stops counting the number of times the ignition switch has been turned from off to ON.

·

Freeze frame data at the time the ABS operates:

The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.

When the ECU stores data at the time a DTC is stored, the data stored during ABS operation is cleared.

·

Freeze frame data at the time a DTC is stored:

When the skid control ECU (brake actuator assembly) stores data at the time a DTC is stored, no updates are performed until the data is cleared.





CHECK FREEZE FRAME DATA


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC / DTC.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509

e.

According to the display on the intelligent tester, select the trouble code data display with freeze frame data.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON : Brake pedal depressed
OFF : Brake pedal released
-
Operated System Operated system status ABS, VSC(TRC), PBA, PB, Unknown, No Sys - ABS : ABS activated
VSC : VSC activated
PBA : PBA activated
PB : PB activated
Sys : System prohibited
Number of IG ON Number of times ignition switch turned to ON after storing freeze frame data 0 to 31 - -
RL Wheel ABS control Rear wheel LH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
RR Wheel ABS control Rear wheel RH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
FL Wheel ABS control Front wheel LH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
FR Wheel ABS control Front wheel RH ABS operation Before or Operate Before : No ABS operation
Operate : During ABS operation
-
Vehicle Speed Maximum wheel speed sensor reading Min. : 0 km/h (0 mph), Max. : 326 km/h (202 mph) Actual vehicle speed The speed which is indicated on the speedometer.
Vehicle Speed Grade Vehicle speed grade Min. : -1.869 G, Max. : 1.854 G Vehicle stopped: -1.869 G During driving: Changes in proportion with vehicle acceleration/deceleration
Time from STP-ON to a control start Elapsed time Min. : 0 Max. : 12.75 s - -
ABS/VSC control continuation time Elapsed time Min. : 0 Max. : 12.75 s - -
ABS/VSC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Number of DTC Number of DTCs stored/Min. : 0 Max. : 255 0 -



CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the freeze frame data.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTCs and freeze frame data (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509