Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (Using the Intelligent Tester)


a.

Check the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: Chassis / ABS/VSC / DTC.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509

vi.

Check the details of the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

HINT:

Refer to the intelligent tester operator's manual for further details.




b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: Chassis / ABS/VSC / DTC.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

vi.

Clear the DTCs by following the prompts on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.





DTC CHECK/CLEAR (Using SST Check Wire)


a.

Check the DTCs.

i.
C249767C12
1.604,0.771 1.417,0.354 true 1.844,1.427 1.844,1.792 true 1.354,0.188 1.646,0.531 0.292,0.344 10 E 1.656,1.813 2.344,2.104 0.688,0.292 10 ECUT 0.167,0.125 0.552,0.49 0.385,0.365 10 *a
*a Front view of DLC3


Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs output from the ABS warning light in the combination meter.

HINT:
·

When the system is normal, the ABS warning light blinks at 0.25 seconds intervals (0.25 seconds on and 0.25 seconds off).

·

When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

·

When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.

·

If 2 or more DTCs are output at the same time, the DTCs will be displayed in ascending order.

·

The codes are explained in Diagnostic Trouble Code Chart (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

If no code is output, inspect the ECUT terminal circuit and ABS warning light circuit.



Trouble Area See procedure
ECUT terminal circuit (See page (Click here))
ABS warning light circuit (Remains on) (See page (Click here))
ABS warning light circuit (Does not come on) (See page (Click here))


iv.

After completing the check, disconnect terminals 13 (ECUT) and 4 (E) of the DLC3.



b.

Clear the DTCs.

i.
C249767C13
1.604,0.771 1.417,0.354 true 1.844,1.427 1.844,1.792 true 1.344,0.188 1.781,0.635 0.438,0.448 10 E 1.646,1.813 2.24,2.115 0.594,0.302 10 ECUT 0.167,0.125 0.469,0.417 0.302,0.292 10 *a
*a Front view of DLC3


Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).


v.

Remove SST from the terminals of the DLC3.




END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.