Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511/11  Torque Sensor 1 Malfunction  C1512/12  Torque Sensor Circuit Malfunction  C1513/13  Torque Sensor Circuit Malfunction  C1514/14  Torque Sensor Power Source Circuit Malfunction  C1517/17  Torque Sensor Hold Malfunction  


DESCRIPTION

The power steering ECU calculates assisting power based on steering torque signals from the torque sensor. If these DTCs are stored in the power steering ECU, the ECU stops steering power assist as a fail-safe function.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1511/11 Torque Sensor 1 Malfunction Torque sensor (TRQ1) signal error or stop
·

Steering column assembly (torque sensor)

·

Power steering ECU


Comes on Ignition switch ON again
C1512/12 Torque Sensor Circuit Malfunction Torque sensor (TRQ2) signal error or stop
·

Steering column assembly (torque sensor)

·

Power steering ECU


Comes on Ignition switch ON again
C1513/13 Torque Sensor Circuit Malfunction The total output voltage of torque sensor (TRQ1) and torque sensor (TRQ2) is out of the specified value*.
·

Steering column assembly (torque sensor)

·

Power steering ECU


Comes on Ignition switch ON again
C1514/14 Torque Sensor Power Source Circuit Malfunction Torque sensor power source voltage error
·

Steering column assembly (torque sensor)

·

Power steering ECU


Comes on Ignition switch ON again
C1517/17 Torque Sensor Hold Malfunction Temporary control due to malfunction related to torque sensor continues for long time
·

Steering column assembly (torque sensor)

·

Power steering ECU


Comes on Ignition switch ON again

*: The total output voltage of torque sensor (TRQ1) and torque sensor (TRQ2) is 4.8 V or lower, or 5.2 V or higher.


C251365C02
0.354,0.26 0.542,0.417 0.188,0.156 10 *a 0.688,2.125 0.875,2.281 0.188,0.156 10 *d 4.646,0.542 4.833,0.698 0.188,0.156 10 *b 4.646,0.802 4.833,0.958 0.188,0.156 10 *c 4.323,4.427 4.51,4.583 0.188,0.156 10 *e 5.906,3.979 6.427,4.135 0.521,0.156 10 (N*m) 1.24,3.979 1.354,4.146 0.115,0.167 10 0 1.24,3.281 1.354,3.448 0.115,0.167 10 1 1.115,2.938 1.344,3.104 0.229,0.167 10 1.5 1.115,1.594 1.344,1.76 0.229,0.167 10 3.5 1.24,1.26 1.354,1.427 0.115,0.167 10 4 1.25,4.135 1.5,4.302 0.25,0.167 10 -20 3.49,4.135 3.594,4.302 0.104,0.167 10 0 5.604,4.135 5.854,4.302 0.25,0.167 10 20
*a Output voltage characteristics with power supply voltage 5 V *b TORQ1
*c TORQ2 *d Output voltage
*e Input torque - -


WIRING DIAGRAM

C245576E02
1.688,2.865 3.865,3.188 2.177,0.323 10 STEERING COLUMN ASSEMBLY 1.656,1.365 2.99,2.01 1.333,0.646 10 POWER STEERING TORQUE SENSOR 5.229,2.896 6.563,3.542 1.333,0.646 10 POWER STEERING ECU ASSEMBLY 5.073,0.938 5.24,1.094 0.167,0.156 10 z2 5.365,0.938 5.771,1.094 0.406,0.156 10 TRQ1 5.365,1.375 5.771,1.531 0.406,0.156 10 TRQV 5.365,1.76 5.771,1.917 0.406,0.156 10 TRQ2 5.365,2.167 5.823,2.323 0.458,0.156 10 TRQG 5.104,0.76 5.229,0.917 0.125,0.156 10 5 5.104,1.208 5.24,1.365 0.135,0.156 10 6 5.104,1.594 5.24,1.76 0.135,0.167 10 7 5.104,2 5.24,2.156 0.135,0.156 10 8 5.063,1.385 5.229,1.542 0.167,0.156 10 z2 5.063,1.771 5.229,1.927 0.167,0.156 10 z2 5.073,2.167 5.24,2.323 0.167,0.156 10 z2

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - POWER STEERING ECU)
a.
C245577C09
2.063,0.563 2.438,0.802 0.375,0.24 0.094,0.031 0.323,0.219 0.229,0.188 10 *a 2.188,0.594 2.354,0.76 0.167,0.167 10 z2
*a Components with harness connected
(Power Steering ECU assembly)


Check the connection condition of the z2 torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER STEERING ECU ASSEMBLY

NG

CONNECT CONNECTOR SECURELY

2.INSPECT POWER STEERING ECU ASSEMBLY
a.
C245577C10
2.073,0.604 2.448,0.833 0.375,0.229 2.333,1.24 2.76,1.844 true 2.208,1.229 1.802,1.823 true 0.094,0.063 0.646,0.396 0.552,0.333 10 *a 1.427,1.844 2.302,2.125 0.875,0.281 10 8 (TRQG) 2.406,1.844 3.167,2.135 0.76,0.292 10 6 (TRQV) 2.188,0.635 2.354,0.802 0.167,0.167 10 z2
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z2-6 (TRQV) - z2-8 (TRQG) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG




OK

3.INSPECT STEERING COLUMN ASSEMBLY (TORQUE SENSOR)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.INSPECT STEERING COLUMN ASSEMBLY (TORQUE SENSOR)
a.
C245577C11
2.052,0.573 2.427,0.802 0.375,0.229 2.385,1.24 2.75,1.844 true 2.271,1.229 1.969,1.833 true 2.208,1.229 1.125,1.844 true 0.094,0.063 0.313,0.26 0.219,0.198 10 *a 0.802,1.865 1.396,2.031 0.594,0.167 10 8 (TRQG) 2.51,1.865 3.104,2.042 0.594,0.177 10 5 (TRQ1) 1.677,1.865 2.271,2.042 0.594,0.177 10 7 (TRQ2) 2.177,0.604 2.375,0.781 0.198,0.177 10 z2
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition (Steering Position) Specified Condition
z2-5 (TRQ1) - z2-8 (TRQG) Engine running, steering wheel not turned (without load) 2.2 to 2.8 V
Engine running, steering wheel turned to right with vehicle stopped 2.2 to 4.85 V
Engine running, steering wheel turned to left with vehicle stopped 0.15 to 2.8 V
z2-7 (TRQ2) - z2-8 (TRQG) Engine running, steering wheel not turned (without load) 2.2 to 2.8 V
Engine running, steering wheel turned to right with vehicle stopped 0.15 to 2.8 V
Engine running, steering wheel turned to left with vehicle stopped 2.2 to 4.85 V



c.

Check the total voltage of Torque Sensor 1 Output and Torque Sensor 2 Output in the Data List.

Chassis > EMPS > Data List
Tester Display
Torque Sensor 1 Output
Torque Sensor 2 Output
50003 317 1,3
Chassis > EMPS > Data List
Tester Display Normal Condition Diagnostic Note
Torque Sensor 1 Output 4.8 to 5.2 V
·

Steering wheel not turned (without load)

·

Steering wheel turned to right with vehicle stopped

·

Steering wheel turned to left with vehicle stopped


Torque Sensor 2 Output 4.8 to 5.2 V
·

Steering wheel not turned (without load)

·

Steering wheel turned to right with vehicle stopped

·

Steering wheel turned to left with vehicle stopped


OK:

A value within the range listed in the normal condition column is displayed on the intelligent tester or Techstream during each steering operation.


Result:
Proceed to
OK
NG




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY