Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1523/23  Motor Circuit Malfunction  C1524/24  Motor Circuit Malfunction  C1555/55  Predriver Malfunction  


DESCRIPTION

The power steering ECU supplies current to the power steering motor through the motor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1523/23 Motor Circuit Malfunction Short (or open) in motor circuit or abnormal voltage in motor circuit.
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on Ignition switch ON again
C1524/24 Motor Circuit Malfunction Short (or open) in motor circuit or abnormal voltage in motor circuit.
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on Ignition switch ON again
C1555/55 Predriver Malfunction Predriver (Motor relay circuit) malfunction
·

Steering column assembly (Power steering motor)

·

Power steering ECU assembly


Comes on Ignition switch ON again

WIRING DIAGRAM

C245578E02
2.042,1.813 3.896,1.979 1.854,0.167 10 POWER STEERING MOTOR 1.469,3.031 3.708,3.375 2.24,0.344 10 STEERING COLUMN ASSEMBLY 4.469,1.604 4.646,1.75 0.177,0.146 10 z1 4.479,2.49 4.667,2.656 0.188,0.167 10 z1 4.51,1.396 4.604,1.563 0.094,0.167 10 1 4.51,2.313 4.646,2.479 0.135,0.167 10 2 4.792,1.604 5.073,1.781 0.281,0.177 10 M1 4.792,2.5 5.031,2.677 0.24,0.177 10 M2 4.354,3.052 6.771,3.375 2.417,0.323 10 POWER STEERING ECU ASSEMBLY 5.625,2.5 5.927,2.667 0.302,0.167 10 E26 5.708,2.302 5.854,2.469 0.146,0.167 10 2 5.25,2.5 5.573,2.667 0.323,0.167 10 GND 4.427,0.635 4.698,0.792 0.271,0.156 10 E26 4.5,0.458 4.615,0.604 0.115,0.146 10 1 4.792,0.635 5.083,0.813 0.292,0.177 10 IGP 2.833,0.844 3.177,1.031 0.344,0.188 10 EPS 0.573,0.615 1.417,0.833 0.844,0.219 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.
C245577C12
1.229,0.125 1.625,0.375 0.396,0.25 0.094,0.073 0.354,0.333 0.26,0.26 10 *a 1.354,0.167 1.542,0.354 0.188,0.188 10 z1
*a Component with harness connected
(Power Steering ECU Assembly)


Check the connection condition of the z1 power steering motor connector.

OK:

Power steering motor connector is securely connected to the power steering ECU assembly.


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER STEERING ECU

NG

CONNECT CONNECTOR SECURELY

2.INSPECT POWER STEERING ECU
a.
C245577C13
0.677,0.073 1.104,0.323 0.427,0.25 1.198,0.073 1.604,0.323 0.406,0.25 0.917,1.188 0.656,1.75 true 1.438,1.188 1.573,1.74 true 1.5,0.969 2.156,1.771 true 0.094,0.042 0.323,0.271 0.229,0.229 10 *a 0.385,1.781 1.26,2.135 0.875,0.354 10 2 (GND) 2,1.781 2.74,2.083 0.74,0.302 10 1 (M1) 1.365,1.781 2.094,2.146 0.729,0.365 10 2 (M2) 0.76,0.115 1.052,0.302 0.292,0.188 10 E26 1.323,0.115 1.5,0.302 0.177,0.188 10 z1
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
(Steering Position)
Specified Condition
z1-1 (M1) - E26-2 (GND) Ignition switch ON, steering wheel turned to right 6 to 8 V
Ignition switch ON, steering wheel turned to left 11 to 14 V
z1-2 (M2) - E26-2 (GND) Ignition switch ON, steering wheel turned to right 11 to 14 V
Ignition switch ON, steering wheel turned to left 6 to 8 V


Result:
Proceed to
OK
NG




OK

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND)
3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
a.
C245579C03
1.49,0.208 1.927,0.458 0.438,0.25 1.792,1.104 2.156,1.104 true 1.25,1.604 1.615,1.604 true 0.177,0.135 0.406,0.323 0.229,0.188 10 *a 1.646,0.25 1.833,0.406 0.188,0.156 10 z1 2.219,1.01 2.583,1.208 0.365,0.198 10 M1 0.958,1.51 1.281,1.688 0.323,0.177 10 M2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the z1 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-1 (M1) - z1-2 (M2) Always Below 1 Ω
z1-1 (M1) - Body ground Always 1 MΩ or higher
z1-2 (M2) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND)

NG

REPLACE STEERING COLUMN ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND)
a.
C245577N01
0.708,0.094 1.146,0.354 0.438,0.26 0.927,1.125 0.667,1.688 true 1.021,0.958 1.302,1.688 true 0.323,1.74 1.021,2.052 0.698,0.313 10 2 (GND) 1.208,1.729 2.031,2.021 0.823,0.292 10 1 (IGP) 0.802,0.135 1.583,0.573 0.781,0.438 10 E26

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-1 (IGP) - Body ground Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

CHECK FOR HARNESS OR CONNECTOR