Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/52  PIG Power Source Circuit  C1553/53  When Resetting Voltage, Vehicle is Being Driven  C1554/54  EPS Relay Circuit  


DESCRIPTION

When a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because each relay is built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1552/52 PIG Power Source Circuit PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU


Comes on Ignition switch ON again
C1553/53 When Resetting Voltage, Vehicle is Being Driven Abnormal over voltage
·

IG and PIG power source circuits

·

Power steering ECU


Comes on Ignition switch ON again
C1554/54 EPS Relay Circuit Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU


Comes on Ignition switch ON again

WIRING DIAGRAM

C248677E04
0.781,1.24 1.646,1.448 0.865,0.208 10 from Battery 3.01,1.438 3.427,1.615 0.417,0.177 10 EPS 2.677,2.323 4.542,2.531 1.865,0.208 10 POWER STEERING MOTOR 4.948,3.917 6.604,4.271 1.656,0.354 10 POWER STEERING ECU ASSEMBLY 4.74,1.26 5.01,1.438 0.271,0.177 10 E26 5.104,1.26 5.427,1.438 0.323,0.177 10 IGP 4.844,1.083 4.948,1.26 0.104,0.177 10 1 4.74,3.333 5.01,3.51 0.271,0.177 10 E26 5.094,3.333 5.427,3.51 0.333,0.177 10 GND 4.844,3.156 4.948,3.333 0.104,0.177 10 2 4.781,1.865 4.979,2.052 0.198,0.188 10 z1 5.125,1.865 5.344,2.042 0.219,0.177 10 M1 4.844,1.688 4.948,1.865 0.104,0.177 10 1 4.781,2.74 5,2.948 0.219,0.208 10 z1 2.688,2.188 2.865,2.365 0.177,0.177 10 z1 5.125,2.75 5.354,2.927 0.229,0.177 10 M2 4.844,2.573 4.948,2.75 0.104,0.177 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (PIG POWER SUPPLY)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester or Techstream on.


d.

Enter the following menus: Chassis / EMPS / Data List.

Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 317 9

e.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the intelligent tester or Techstream.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to activate motor Min: 0 V
Max: 21.1531 V
11 to 14 V Power steering is in operation
OK:

The normal condition value is displayed on the intelligent tester or Techstream.


Result:
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)

B

REPLACE POWER STEERING ECU

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
C245577N03
0.729,0.073 1.177,0.333 0.448,0.26 0.927,1.125 0.667,1.688 true 1.021,0.958 1.302,1.688 true 0.323,1.708 0.885,1.906 0.563,0.198 10 2 (GND) 1.208,1.729 1.74,1.938 0.531,0.208 10 1 (IGP) 0.813,0.115 1.208,0.281 0.396,0.167 10 E26

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
E26-1 (IGP) - Body ground Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
E27-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
a.
C245579C04
1.469,0.198 1.958,0.49 0.49,0.292 1.802,1.104 2.167,1.104 true 1.219,1.604 1.583,1.604 true 0.177,0.135 0.385,0.323 0.208,0.188 10 *a 1.635,0.26 1.802,0.417 0.167,0.156 10 z1 2.24,1.01 2.49,1.188 0.25,0.177 10 M1 0.958,1.51 1.219,1.708 0.26,0.198 10 M2
*a Front view of wire harness connector
(to Power Steering ECU)


Disconnect the z1 power steering ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z1-1 (M1) - z1-2 (M2) Always Below 1 Ω
z1-1 (M1) - Body ground Always 1 MΩ or higher
z1-2 (M2) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE POWER STEERING ECU

NG

REPLACE STEERING COLUMN ASSEMBLY