Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU detects a malfunction, the P/S warning light comes on. At this time, the power steering ECU stores the appropriate DTC.

WIRING DIAGRAM

C248678E02
0.115,1.125 1.375,1.313 1.26,0.188 10 from Ignition Switch 1.896,1.313 2.469,1.458 0.573,0.146 10 ECU IG2 3.813,1.313 4.125,1.469 0.313,0.156 10 EPS 3.021,1.021 3.198,1.167 0.177,0.146 10 IG 4.583,1.021 5.031,1.167 0.448,0.146 10 EPSW 2.719,1.854 5.063,2.177 2.344,0.323 10 COMBINATION METER ASSEMBLY 2.76,1.021 2.948,1.177 0.188,0.156 10 39 5.083,1.021 5.292,1.198 0.208,0.177 10 16 5.865,1.104 6.021,1.271 0.156,0.167 10 W 5.542,1.719 5.823,1.875 0.281,0.156 10 E27 5.677,1.021 5.813,1.208 0.135,0.188 10 9 5.531,1.906 6.844,2.552 1.313,0.646 10 POWER STEERING ECU ASSEMBLY 2.74,1.688 3.021,1.844 0.281,0.156 10 E34

PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 317

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

OK:

DTC is not output.


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER STEERING ECU

NG

2.INSPECT POWER STEERING ECU
a.
C245577C15
1.698,0.625 2.115,0.875 0.417,0.25 1.958,1.229 1.698,1.719 true 1.781,0.667 2.083,0.823 0.302,0.156 10 E27 1.542,1.729 1.917,1.938 0.375,0.208 10 9 (W) 0.125,0.094 0.438,0.292 0.313,0.198 10 *a
*a Component with harness connected
(Power Steering ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E27-9 (W) - Body ground Ignition switch off → ON
(Bulb check function)
For approximately 2 seconds 11 to 14 V → Below 1 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - COMBINATION METER)

NG

REPLACE POWER STEERING ECU

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - COMBINATION METER)
a.

Disconnect the E34 combination meter connector.


b.

Disconnect the E27 power steering ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E34-15 (EPSW) - E27-9 (W) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E27-9 (W) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR