Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DTC CHECK / CLEAR  


CHECK DTCs


a.

When using an intelligent tester or Techstream;

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester or Techstream to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester or Techstream on.


v.

Read the DTCs by following the prompts on the tester screen. Enter the following menus: Chassis / EMPS / DTC.

Chassis > EMPS > Trouble Codes
50001 317



b.

When not using an intelligent tester or Techstream;

i.
C193959C09
1.031,1.854 1.146,1.854 1.146,1.854 1.375,1.083 true 2.094,0.396 1.896,0.396 1.896,0.396 1.583,0.906 true 0.042,0.021 0.323,0.188 0.281,0.167 10 *a 0.375,1.781 0.99,1.958 0.615,0.177 10 EPS TS 2.146,0.323 2.333,0.469 0.188,0.146 10 E
*a Front view of DLC3


Turn the ignition switch off.


ii.

Using SST, connect terminals 3 (EPS TS) and 4 (E) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.
F102336E01
0.979,3 1.083,3.365 false 1.167,3.375 1.313,2.74 false 1.458,3.375 1.563,3.01 false 1.906,3.375 2.104,2.844 false 2.26,3.375 2.385,3.042 false 1.281,0.156 2.229,0.365 0.948,0.208 10 Normal Code: 1.198,2.219 2.427,2.396 1.229,0.177 10 Codes 21 and 22: 2.677,1.917 3.385,2.115 0.708,0.198 10 (seconds) 2.708,4.271 3.406,4.458 0.698,0.188 10 (seconds) 2.208,0.563 2.573,0.74 0.365,0.177 10 0.25 1.135,0.813 1.51,1 0.375,0.188 10 0.25 0.479,1.24 0.792,1.438 0.313,0.198 10 ON 0.229,3.292 0.542,3.49 0.313,0.198 10 ON 0.479,1.656 0.938,1.854 0.458,0.198 10 OFF 0.229,3.792 0.688,3.99 0.458,0.198 10 OFF 1.042,4.042 1.635,4.24 0.594,0.198 10 Code 21 2.313,4.031 2.885,4.208 0.573,0.177 10 Code 22 0.823,3.385 0.979,3.583 0.156,0.198 10 4 0.823,2.813 1.167,3 0.344,0.188 10 0.5 1.219,2.563 1.552,2.75 0.333,0.188 10 0.5 2.323,2.833 2.781,3.031 0.458,0.198 10 0.5 1.51,2.823 1.823,3 0.313,0.177 10 1.5 2.031,2.635 2.49,2.833 0.458,0.198 10 2.5

Read and write down any DTCs indicated by the EPS warning light on the combination meter. Refer to the chart on the left for examples of a normal code and DTCs 21 and 22.

HINT:
·

If the EPS warning light does not blink to display any DTCs set or the normal code, inspect the circuit shown in the table below.

Trouble Area See Page
EPS warning light circuit See page (Click here)

·

If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order.




v.

Refer to the Diagnostic Trouble Code Chart (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART) for DTC information.




CLEAR DTCs


a.

When using an intelligent tester or Techstream;

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester or Techstream to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester or Techstream on.


v.

Operate the intelligent tester or Techstream to clear the codes. Enter the following menus: Chassis / EMPS / DTC / Clear.

Chassis > EMPS > Clear DTCs
50002 317


b.

When not using an intelligent tester or Techstream;

i.
C193959C10
1.031,1.854 1.146,1.854 1.146,1.854 1.375,1.083 true 2.094,0.396 1.896,0.396 1.896,0.396 1.583,0.906 true 0.042,0.021 0.313,0.208 0.271,0.188 10 *a 0.375,1.781 1,1.938 0.625,0.156 10 EPS TS 2.146,0.323 2.365,0.5 0.219,0.177 10 E
*a Front view of DLC3


Turn the ignition switch off.


ii.

Using SST, connect terminals 3 (EPS TS) and 4 (E) of the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Disconnect the SST check wire from terminal 4 (E) and reconnect it, and repeat this procedure 4 times or more within 8 seconds.


v.

Check that the EPS warning light blinks a code to indicate normality.