Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM D

NETWORKING  CAN COMMUNICATION SYSTEM  SYSTEM DESCRIPTION  


BRIEF DESCRIPTION


a.

The Controller Area Network (CAN) is a serial data communication system for real time application. It is a vehicle multiplex communication system which has a high communication speed and the ability to detect malfunctions.

C238999E03
1.167,2.135 1.427,2.135 1.427,2.135 1.427,1.771 true 4.25,3.25 4.51,3.25 4.51,3.25 4.75,3.021 true 0.208,2.031 1.719,2.583 1.51,0.552 10 CAN Main Bus 3.438,3.146 4.604,3.625 1.167,0.479 10 CAN Branch 1.406,3.646 4,4.323 2.594,0.677 10 : CAN Main Bus Line (CANH) 1.417,4.073 3.969,4.771 2.552,0.698 10 : CAN Main Bus Line (CANL) 4.823,3.635 6.917,4.115 2.094,0.479 10 : CAN Branch Line (CANH) 4.823,4.052 6.906,4.625 2.083,0.573 10 : CAN Branch Line (CANL) 1.708,2.625 2.521,3.125 0.813,0.5 10 DLC3 3.396,2.625 4.313,3.229 0.917,0.604 10 ECU 5.302,2.625 6.177,3.146 0.875,0.521 10 ECU


b.

Using the CANH and CANL bus lines as a pair, CAN communication is performed using a voltage differential. (A base voltage is applied to the pair of lines and a voltage differential is created when communicating.)


c.

Many ECUs installed on the vehicle operate by sharing information and communicating with each other.


d.

The CAN has two resistors of 120 Ω which are necessary to enable communication.


e.

Control system CAN is composed of one bus.



DEFINITION OF TERMS


a.

Main bus line

i.

The main bus line is a wire harness between the two terminating resistors on the bus. This is the main bus in the CAN communication system.



b.

Branch line

i.

The branch line is a wire harness which diverges from the main bus line to an ECU.



c.

Terminating resistors

i.

Two resistors of 120 Ω are installed in parallel across the ends of the CAN main bus lines. They are called terminating resistors. These resistors allow the changes of the voltage differential between the CAN bus lines to be accurately judged. To allow proper function of CAN communication, it is necessary to have both terminating resistors installed. Since the two resistors are installed in parallel, this results in a measurement of approximately 60 Ω.




ECUS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

ECM


ii.

TCM*1


iii.

Combination meter assembly*2

HINT:

*1 : for A/T

*2 : w/ Multi Information Display





CIRCUIT DESCRIPTION


a.

The V bus has termination circuits with two resistors of 120 Ω.



TROUBLESHOOTING REMARKS


a.

DTCs for the CAN communication system can be checked using the intelligent tester or Techstream. The DLC3 is connected to the CAN communication system, but no DTCs exist regarding problems in the DLC3 or the DLC3 branch lines. If there is any trouble in the DLC3 or the DLC3 branch lines, ECUs on the CAN network cannot output codes to the intelligent tester or Techstream.


b.

Trouble in the CAN V bus (communication lines) can be checked by measuring the resistance between terminals of the DLC3. However, an open circuit in a branch line other than the DLC3 branch lines cannot be checked from the DLC3 (except branch line of the DLC3).

NOTICE:

Do not insert the tester probes directly into the DLC3. Be sure to use service wires.




DIAGNOSTIC TROUBLE CODES FOR CAN COMMUNICATION SYSTEM


HINT:

See Diagnosis System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HOW TO DISTINGUISH CONNECTOR OF CAN JUNCTION CONNECTOR


a.

In the CAN communication system, the shape of connectors connected to the CAN junction connector which has an earth terminal is the same. The connectors connected to the CAN junction connector can be distinguished by the colors of the bus lines and the connecting side of the junction connector.

HINT:

See Terminals of ECU for bus line color or the shape of connecting surface (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).