Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).
·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C243547E03
5.156,5.188 6.208,5.76 1.052,0.573 10 Trouble Area 1.281,2.063 1.885,2.542 0.604,0.479 10 DLC3 0.177,4.615 0.813,5.073 0.635,0.458 10 ECM 2.167,4.656 3.771,5.51 1.604,0.854 10 CAN NO. 1 JUNCTION CONNECTOR* 4.354,4.802 6.833,5.281 2.479,0.479 10 COMBINATION METER ASSEMBLY 5.375,3.24 5.844,3.635 0.469,0.396 10 +B 5.396,3.896 5.583,4.094 0.188,0.198 10 IG 5.427,4.344 5.74,4.646 0.313,0.302 10 E 4.365,3.719 5.031,4.135 0.667,0.417 10 CANL 4.375,3.104 5.031,3.552 0.656,0.448 10 CANH 0.542,4.063 1.115,4.448 0.573,0.385 10 120 Ω 4.719,4.031 5.417,4.458 0.698,0.427 10 120 Ω 5.656,3.76 6.115,4.156 0.458,0.396 10 39 5.646,3.135 6.135,3.563 0.49,0.427 10 40 5.635,4.26 6.063,4.646 0.427,0.385 10 16 4.115,3.094 4.479,3.427 0.365,0.333 10 28 4.115,3.719 4.458,4.146 0.344,0.427 10 29 5.917,4.052 6.729,4.406 0.813,0.354 10 ECU IG2 5.896,3.396 6.708,3.813 0.813,0.417 10 BACK UP 4.344,4.594 4.833,4.896 0.49,0.302 10 E34 1.333,0.594 3.313,1.052 1.979,0.458 10 : CAN Main Bus Line (CANH) 1.333,0.938 3.323,1.49 1.99,0.552 10 : CAN Main Bus Line (CANL) 1.333,1.302 3.49,1.927 2.156,0.625 10 : CAN Branch Bus Line (CANH) 1.333,1.635 3.5,2.167 2.167,0.531 10 : CAN Branch Bus Line (CANL) 0.188,5.042 1.094,5.51 0.906,0.469 10 * : for A/T

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>Combination Meter ECU Communication Stop Mode).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C243545C01
1.417,0.615 1.906,0.906 0.49,0.292 1.188,2.375 0.896,2.26 false 1.833,2.167 1.594,2.771 true 1.927,2.167 2.156,2.771 true 0.125,0.115 0.5,0.5 0.375,0.385 10 *a 1.51,0.677 2,1.083 0.49,0.406 10 E34 0.938,2.698 1.823,3.156 0.885,0.458 10 29 (CANL) 2.219,2.781 3.083,3.188 0.865,0.406 10 28 (CANH)
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-28 (CANH) - E34-29 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN LINE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C243545C05
1.417,0.615 1.906,0.906 0.49,0.292 1.188,2.375 0.896,2.26 false 0.844,1.615 1.26,2.042 true 0.948,2.177 0.667,2.469 true 1.063,2.177 1.656,2.76 true 0.125,0.115 0.542,0.469 0.417,0.354 10 *a 1.51,0.677 1.802,0.833 0.292,0.156 10 E34 0.177,2.417 0.875,2.771 0.698,0.354 10 40 (+B) 1.708,2.708 2.344,3.021 0.635,0.313 10 39 (IG) 0.427,1.479 0.969,1.854 0.542,0.375 10 16 (E)
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-16 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E34-39 (IG) - Body ground Ignition switch ON 11 to 14 V
E34-40 (+B) - Body ground Always 11 to 14 V


Result:
proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)