Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Transmission Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Transmission Control ECU Communication Stop Mode Either condition is met:
·

"ECT" is not displayed on the "CAN Bus Check" screen of the intelligent tester or Techstream (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Transmission Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

TCM branch line or connector

·

Power source circuit of TCM

·

TCM ground circuit

·

TCM



WIRING DIAGRAM

C243548E03
4.01,1.135 4.344,0.552 4.344,0.552 4.688,0.552 true 3.24,4.448 3.75,4.875 0.51,0.427 10 E9 0.094,0.094 2.438,0.552 2.344,0.458 12 w/ Multi Information Display : 5.635,3.885 6.604,4.365 0.969,0.479 10 Trouble Area 1.469,0.49 1.99,0.885 0.521,0.396 10 DLC3 0.323,2.688 0.896,3.094 0.573,0.406 10 ECM 4.729,0.479 6.333,1.271 1.604,0.792 10 CAN NO. 1 JUNCTION CONNECTOR 5.729,2.708 7.042,3.365 1.313,0.656 10 COMBINATION METER ASSEMBLY 4.104,3.146 4.708,3.542 0.604,0.396 10 CANL 4.5,3.75 4.948,4.104 0.448,0.354 10 E01 4.573,3.427 5.01,3.802 0.438,0.375 10 E1 3.375,3.729 3.885,4.125 0.51,0.396 10 BAT 3.375,3.385 3.969,3.781 0.594,0.396 10 BAT2 3.375,4.021 3.865,4.448 0.49,0.427 10 +B 4.5,4.063 4.99,4.469 0.49,0.406 10 E02 3.604,3.146 4.177,3.5 0.573,0.354 10 CANH 2.24,3.521 2.917,3.906 0.677,0.385 10 ECU-B 2.24,4.323 3.042,4.719 0.802,0.396 10 ECU IG2 0.719,2.052 1.313,2.427 0.594,0.375 10 120 Ω 6.208,2.063 6.771,2.458 0.563,0.396 10 120 Ω 3.198,3.271 3.635,3.646 0.438,0.375 10 1 4.833,3.323 5.24,3.677 0.406,0.354 10 4 4.833,3.635 5.198,3.958 0.365,0.323 10 6 4.833,3.948 5.281,4.292 0.448,0.344 10 5 3.198,3.583 3.594,3.938 0.396,0.354 10 2 3.198,4.063 3.583,4.458 0.385,0.396 10 3 4.302,2.917 4.646,3.208 0.344,0.292 10 17 3.917,2.917 4.219,3.219 0.302,0.302 10 7 1.448,5.135 3.385,5.615 1.938,0.479 10 : CAN Main Bus Line (CANH) 1.448,5.427 3.406,5.823 1.958,0.396 10 : CAN Main Bus Line (CANL) 4.448,5.167 6.563,5.729 2.115,0.563 10 : CAN Branch Bus Line (CANH) 4.469,5.438 6.635,5.792 2.167,0.354 10 : CAN Branch Bus Line (CANL) 3.24,4.625 3.708,5.021 0.469,0.396 10 TCM

C243559E03
5.198,5.177 6.177,5.688 0.979,0.51 10 Trouble Area 1.25,2.063 1.76,2.448 0.51,0.385 10 DLC3 0.177,4.635 0.76,5.104 0.583,0.469 10 ECM 4.323,4.552 4.896,4.917 0.573,0.365 10 E9 4.365,3.719 4.948,4.094 0.583,0.375 10 CANL 4.375,3.073 4.948,3.427 0.573,0.354 10 CANH 0.49,3.969 1.177,4.333 0.688,0.365 10 120 Ω 4.729,4 5.375,4.375 0.646,0.375 10 120 Ω 5.667,3.333 6.031,3.646 0.365,0.313 10 3 4.188,3.073 4.542,3.406 0.354,0.333 10 7 4.115,3.708 4.573,4.073 0.458,0.365 10 17 1.333,0.604 3.26,1.042 1.927,0.438 10 : CAN Main Bus Line (CANH) 1.333,0.938 3.458,1.458 2.125,0.521 10 : CAN Main Bus Line (CANL) 1.333,1.292 3.615,1.833 2.281,0.542 10 : CAN Branch Bus Line (CANH) 1.333,1.635 3.635,2.177 2.302,0.542 10 : CAN Branch Bus Line (CANL) 4.323,4.729 4.865,5.177 0.542,0.448 10 TCM 0.115,0.135 2.542,0.604 2.427,0.469 12 w/o Multi Information Display : 5.313,4.052 5.813,4.385 0.5,0.333 10 E01 5.385,3.729 5.802,4.094 0.417,0.365 10 E1 5.313,3.073 5.781,3.51 0.469,0.438 10 BAT 5.219,2.771 5.698,3.198 0.479,0.427 10 BAT2 5.385,3.417 5.781,3.76 0.396,0.344 10 +B 5.313,4.344 5.781,4.677 0.469,0.333 10 E02 5.969,2.927 6.635,3.292 0.667,0.365 10 ECU-B 5.927,3.625 6.708,3.99 0.781,0.365 10 ECU IG2 5.646,2.667 5.979,3.01 0.333,0.344 10 1 5.646,3.635 6.01,3.938 0.365,0.302 10 4 5.646,3.969 6.031,4.292 0.385,0.323 10 6 5.646,4.26 6.01,4.583 0.365,0.323 10 5 5.667,3 6.021,3.344 0.354,0.344 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>Transmission Control ECU Communication Stop Mode).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (TCM BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C243543C01
1.146,0.583 1.635,0.875 0.49,0.292 1.625,2.26 1.969,2.719 true 2.031,2.052 1.635,2.188 true 0.094,0.083 0.49,0.417 0.396,0.333 10 *a 1.292,0.635 1.75,1.01 0.458,0.375 10 E9 2.104,1.99 2.927,2.323 0.823,0.333 10 7 (CANH) 2.052,2.646 2.948,3 0.896,0.354 10 17 (CANL)
*a Rear view of wire harness connector
(to TCM)


Disconnect the E9 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9-7 (CANH) - E9-17 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TCM BRANCH LINE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C243543C02
1.146,0.583 1.635,0.875 0.49,0.292 2.198,1.719 1.438,2.104 true 1.615,2.135 2.375,2.531 true 1.167,2.135 0.677,2.385 true 0.885,1.646 1.25,2.115 true 1.531,2.135 1.896,2.604 true 1.323,2.135 0.958,2.604 true 0.094,0.083 0.49,0.427 0.396,0.344 10 *a 1.271,0.635 1.708,1.021 0.438,0.385 10 E9 2.292,1.635 2.948,2 0.656,0.365 10 3 (+B) 2.448,2.469 3.188,2.833 0.74,0.365 10 1 (BAT2) 0.052,2.313 0.771,2.667 0.719,0.354 10 6 (E01) 1.583,2.688 2.396,3.052 0.813,0.365 10 2 (BAT) 0.635,2.656 1.313,3 0.677,0.344 10 4 (E1) 0.281,1.542 0.938,1.917 0.656,0.375 10 5 (E02)
*a Rear view of wire harness connector
(to TCM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9-4 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E9-5 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E9-6 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E9-1 (BAT2) - Body ground Always 11 to 14 V
E9-2 (BAT) - Body ground Always 11 to 14 V
E9-3 (+B) - Body ground ignition switch ON 11 to 14 V


Result:
proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)