Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015187 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  No Answer-back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning lights and security buzzer* do not answer-back. In such a case, the hazard warning light signal and security buzzer signal* output from the door control receiver may be malfunctioning.

*: w/ Theft Warning ECU Assembly


HINT:

The security buzzer is built into the theft warning ECU assembly.


WIRING DIAGRAM

B291406E02
0.292,3.594 2.115,4.073 1.823,0.479 10 HAZARD WARNING SIGNAL SWITCH ASSEMBLY 0.302,3.417 0.854,3.844 0.552,0.427 10 E8 0.354,2.146 2.469,2.76 2.115,0.615 10 DOOR CONTROL RECEIVER 0.365,1.979 1.031,2.365 0.667,0.385 10 E62 0.406,2.938 0.813,3.292 0.406,0.354 10 4 1.823,2.938 2.146,3.292 0.323,0.354 10 3 2.625,0.719 2.969,1.052 0.344,0.333 10 7 2.208,0.729 2.583,1.031 0.375,0.302 10 *1 2.208,0.344 2.698,0.708 0.49,0.365 10 *1 2.625,0.333 2.948,0.635 0.323,0.302 10 2 1.813,0.729 2.313,1.115 0.5,0.385 10 9 1.208,0.813 2,1.156 0.792,0.344 10 AOUT*1 1.813,0.344 2.146,0.667 0.333,0.323 10 10 2.813,0.802 3.542,1.156 0.729,0.354 10 ROUT 2.813,0.427 3.302,0.74 0.49,0.313 10 RIN 1.365,0.427 2.073,0.885 0.708,0.458 10 AIN*1 1.813,1.656 2.24,1.99 0.427,0.333 10 17 1.438,1.75 1.885,2 0.448,0.25 10 CHR 4.573,3.073 7.115,3.781 2.542,0.708 10 to Side Turn Signal Light Assembly LH*2 4.573,3.406 7.115,4.104 2.542,0.698 10 to Rear Combination Light Assembly LH 4.573,2.75 6.531,3.354 1.958,0.604 10 to Headlight Assembly LH 4.573,2.042 7.104,2.698 2.531,0.656 10 to Side Turn Signal Light Assembly RH*2 4.573,2.375 7.156,2.969 2.583,0.594 10 to Rear Combination Light Assembly RH 4.573,1.719 6.448,2.313 1.875,0.594 10 to Headlight Assembly RH 2.625,1.656 3.021,1.979 0.396,0.323 10 8 3.573,1.635 4.125,2.063 0.552,0.427 10 2 3.573,2.677 3.927,3.042 0.354,0.365 10 3 2.802,1.75 3.406,2.115 0.604,0.365 10 EHW 3.292,1.74 3.75,2.135 0.458,0.396 10 LR 3.313,2.771 3.729,3.188 0.417,0.417 10 LL 2.177,4.031 4.635,4.323 2.458,0.292 10 TURN SIGNAL FLASHER ASSEMBLY 2.188,3.865 2.708,4.167 0.521,0.302 10 E35 2.031,1.177 4.75,1.698 2.719,0.521 10 THEFT WARNING ECU ASSEMBLY*1 2.031,1.01 2.49,1.323 0.458,0.313 10 J12 2.552,4.354 5.531,4.677 2.979,0.323 10 *2: for Front Fender Type Side Turn Signal Light 0.063,4.344 2.344,4.708 2.281,0.365 10 *1: w/ Theft Warning ECU Assembly

PROCEDURE

1.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation by wireless door lock control function.

Result:
Result Proceed to
Only hazard warning light answer-back does not occur. A
Only security buzzer answer-back does not occur.* B


*: w/ Theft Warning ECU Assembly




A

2.CHECK HAZARD WARNING LIGHTS

B

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - THEFT WARNING ECU ASSEMBLY)
2.CHECK HAZARD WARNING LIGHTS
a.

Check that the hazard warning lights flash continuously when the hazard warning signal switch assembly is pressed.

OK:

Hazard warning lights flash continuously.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TURN SIGNAL FLASHER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TURN SIGNAL FLASHER ASSEMBLY)
a.

Disconnect the E62 door control receiver connector.


b.

Disconnect the E35 turn signal flasher assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E62-17 (CHR) - E35-8 (EHW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E62-17 (CHR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - THEFT WARNING ECU ASSEMBLY)
a.

Disconnect the E62 door control receiver connector.


b.

Disconnect the J12 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E62-10 (AIN) - J12-2 (RIN) Always Below 1 Ω
E62-9 (AOUT) - J12-7 (ROUT) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E62-10 (AIN) - Body ground Always 10 kΩ or higher
E62-9 (AOUT) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR