Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2793/23  Key ID Code not Registered  B2794/22  Unmatched Encryption Code  B2797/24  Communication Malfunction No .1, Transponder Communication Malfunction  B2798/25  Communication Malfunction No. 2, Incomplete Communication with Transponder  


DESCRIPTION

DTC B2793/23 is stored when a malfunction is found in the key during key code registration or a key code is not registered normally. Replace the key if key code registration cannot be performed normally and this DTC is output.

DTC B2794/22 is stored when key codes are mismatched during the transponder communication is inserted into the ignition key cylinder.

DTC B2797/24 is stored when a key with a BCC malfunction is inserted into the ignition key cylinder.

DTC B2798/25 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2793/23 Key ID Code not Registered A transponder chip malfunction (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.



B2794/22 Unmatched Encryption Code When key codes are mismatched during the transponder communication is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.



B2797/24 Communication Malfunction No .1, Transponder Communication Malfunction A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.



B2798/25 Communication Malfunction No. 2, Incomplete Communication with Transponder Key code identification cannot be completed within the specified time (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.




*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation When Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2793/23 -
B2794/22 -
B2797/24 -
B2798/25 -

CAUTION / NOTICE / HINT

NOTICE:
·

When the key is replaced, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs .

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 103
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs using all registered keys.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 103
HINT:

If a DTC is stored, check for DTCs with the next key after clearing the DTCs.


OK:

DTC B2793/23, B2974/22, B2797/24 or B2798/25 is not output.


Result:
Result Proceed to
OK A
NG (all keys) B
NG (any key) C




A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE KEY THAT CANNOT START ENGINE