Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

for Automatic Transmission:

The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the ECM.

for Manual Transmission:

The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speedometer sensor.

WIRING DIAGRAM

E236725E03
2.26,0.625 2.719,1.021 0.458,0.396 10 11 2.26,2.01 2.719,2.427 0.458,0.417 10 22 5.313,0.615 5.76,0.979 0.448,0.365 10 12 4.24,1.417 4.688,1.844 0.448,0.427 10 *2 3.344,0.615 3.896,1.104 0.552,0.49 10 *1 4.896,2.031 5.333,2.438 0.438,0.406 10 *3 1.51,1.396 2.323,1.865 0.813,0.469 10 TCM*1 0.823,2.813 3.125,3.469 2.302,0.656 10 Skid Control ECU Assembly*2 5.104,5.24 7.094,5.677 1.99,0.438 10 Combination Meter Assembly 2.125,3.656 2.979,4.052 0.854,0.396 10 ECU IG2 0.177,3.479 1.802,3.885 1.625,0.406 10 from Ignition Switch 3.063,4.125 4.948,4.594 1.885,0.469 10 Speedometer Sensor*3 0.135,5.323 3.927,5.781 3.792,0.458 10 *3: for Manual Transmission w/o Anti-lock Brake System 0.135,5.01 3.625,5.313 3.49,0.302 10 *2: w/ Anti-lock Brake System 0.135,4.688 4.427,5.208 4.292,0.521 10 *1: for Automatic Transmission w/o Anti-lock Brake System 5.104,5.083 5.635,5.448 0.531,0.365 10 E34 3.063,3.969 3.615,4.365 0.552,0.396 10 E50 0.823,2.646 1.458,3.115 0.635,0.469 10 B10 1.51,1.25 2.031,1.656 0.521,0.406 10 E9 4.313,3.24 4.594,3.542 0.281,0.302 10 1 4.313,3.615 4.76,4.073 0.448,0.458 10 2 3.219,3.396 3.542,3.75 0.323,0.354 10 3 3.917,3.333 4.479,3.698 0.563,0.365 10 OUT 1.771,0.708 2.417,1.156 0.646,0.448 10 SPDO 5.573,0.708 6.292,1.156 0.719,0.448 10 SPDI 1.75,2.094 2.458,2.604 0.708,0.51 10 VWOT 3.917,3.708 4.458,4.094 0.542,0.385 10 GND 3.385,3.49 3.833,3.823 0.448,0.333 10 IG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (VEHICLE SPEED SIGNAL)
E258533C01
1.479,0.167 1.969,0.427 0.49,0.26 0.677,2.104 1.542,1.177 true 0.156,0.146 0.521,0.469 0.365,0.323 10 *a 0.479,2.167 1.229,2.542 0.75,0.375 10 SPDI 2.729,3.781 3.375,4.24 0.646,0.458 10 GND 1.594,0.219 2.115,0.521 0.521,0.302 10 E34
*a Component with harness connected
(Combination Meter Assembly)


a.

Using an oscilloscope, check the signal waveform.

OK:

Waveform is as shown in the illustration.


Item Content
Tester Connection E34-12 (SPDI) - Body ground
Tool Setting 5 V/DIV, 10 ms/DIV
Condition Vehicle speed at 20 km/h

HINT:

As vehicle speed increases, the wavelength shortens.


Result:
Result Proceed to
OK A
NG (for Automatic Transmission w/o Anti-lock Brake System) B
NG (w/ Anti-lock Brake System) C
NG (for Manual Transmission w/o Anti-lock Brake System) D




A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (TCM - COMBINATION METER ASSEMBLY)

C

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

D

4.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TCM - COMBINATION METER ASSEMBLY)
a.

Disconnect E9 TCM connector.


b.

Disconnect E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E9-11 (SPDO) - E34-12 (SPDI) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E9-11 (SPDO) or E34-12 (SPDI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect B10 skid control ECU assembly connector.


b.

Disconnect E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E10-22 (VWOT) E34-12 (SPDI) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E10-22 (VW0T) E34-12 (SPDI)Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE SKID CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - BATTERY AND BODY GROUND)
E236726C01
1.479,0.083 1.969,0.375 0.49,0.292 2.115,1.26 2.635,1.594 true 1.625,1.24 0.979,1.75 true 0.635,1.719 1.344,2.146 0.708,0.427 10 GND 2.688,1.552 3.063,1.906 0.375,0.354 10 IG 0.104,0.104 0.5,0.438 0.396,0.333 10 *a 1.604,0.146 2.26,0.521 0.656,0.375 10 E50
*a Front view of harness connector
(to Speedometer Sensor)


a.

Disconnect the E50 speedometer sensor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E50-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E50-2 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the E50 speedometer sensor connector.


b.

Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E50-1 (OUT) - E34-12 (SPDI) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E50-1 (OUT) or E34-12 (SPDI)- Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR