Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015209 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Pad Switch)

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with a new one:

Scratches, cracks, dents or chips in the connector or spiral cable sub-assembly.


b.
B296834C01
2.25,3.208 2.667,3.458 0.417,0.25 1.5,3.208 1.917,3.458 0.417,0.25 1.833,0.385 2.25,0.635 0.417,0.25 0.771,0.667 1.063,0.823 0.292,0.156 10 A 2.323,3.25 2.615,3.406 0.292,0.156 10 E63 1.573,3.25 1.865,3.406 0.292,0.156 10 E32 1.948,0.427 2.24,0.583 0.292,0.156 10 z3 0.083,0.063 0.313,0.281 0.229,0.219 10 *a
*a Component without harness connected
(Spiral Cable Sub-assembly)


Check the spiral cable sub-assembly.

i.

Set the spiral cable sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
E63-1 (D+) - A-1 Always Below 1 Ω
E63-2 (D-) - A-2 Always Below 1 Ω
E32-1 (+) - z3-1 Always Below 1 Ω
E32-2 (IL+2) - z3-2 Always Below 1 Ω
E32-3 (AU1) - z3-3 Always Below 1 Ω
E32-4 (AU2) - z3-4 Always Below 1 Ω
E32-5 (EAU) - z3-5 Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then, while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
E63-1 (D+) - A-1 Always Below 1 Ω
E63-2 (D-) - A-2 Always Below 1 Ω
E32-1 (+) - z3-1 Always Below 1 Ω
E32-2 (IL+2) - z3-2 Always Below 1 Ω
E32-3 (AU1) - z3-3 Always Below 1 Ω
E32-4 (AU2) - z3-4 Always Below 1 Ω
E32-5 (EAU) - z3-5 Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.

NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Hide 84306 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Pad Switch)

a.

If there are any defects as mentioned below, replace the spiral cable sub-assembly with sensor with a new one:

Scratches, cracks, dents or chips in the connector or spiral cable sub-assembly.


b.
B296833C01
1.917,3.417 2.333,3.667 0.417,0.25 1.25,3.417 1.667,3.667 0.417,0.25 2,0.219 2.417,0.469 0.417,0.25 0.458,1.396 0.75,1.552 0.292,0.156 10 A 2,3.469 2.292,3.625 0.292,0.156 10 E54 1.333,3.469 1.625,3.625 0.292,0.156 10 E55 2.135,0.25 2.427,0.406 0.292,0.156 10 z4 0.135,0.052 0.417,0.292 0.281,0.24 10 *a
*a Component without harness connected
(Spiral Cable Sub-assembly)


Check the spiral cable sub-assembly.

i.

Set the spiral cable sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
E55-1 (D+) - A-1 Always Below 1 Ω
E55-2 (D-) - A-2 Always Below 1 Ω
E54-1 (+) - z4-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then, while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


Standard Resistance:
Tester Connection Condition Specified Condition
E55-1 (D+) - A-1 Always Below 1 Ω
E55-2 (D-) - A-2 Always Below 1 Ω
E54-1 (+) - z4-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.

NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.