Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015212 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

·

When installing the front airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.



PROCEDURE

Hide 89173A 1.INSTALL FRONT AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the sensor connector to the front airbag sensor.

i.

Check that the terminal housing is in the unlock position.

H103032C01
1.938,1.333 2.188,1.333 2.188,1.333 2.188,1.083 true 2.542,1.333 2.292,1.333 2.292,1.333 2.292,1.021 true 5.667,1.25 5.833,1.25 5.833,1.25 5.833,0.896 true 6.333,0.25 6.5,0.167 6.5,0.167 6.667,0.167 false 1.917,2.583 2.25,2.583 2.25,2.583 2.25,2.417 true 2.667,2.615 2.417,2.615 2.417,2.615 2.417,2.365 true 5.75,2.583 5.917,2.583 5.917,2.583 5.917,2.198 true 6.073,1.583 6.083,1.333 6.083,1.333 6.333,1.333 false 1,0.417 1.313,0.615 0.313,0.198 10 *a 4.417,0.417 4.729,0.615 0.313,0.198 10 *a 1,1.833 1.313,2.031 0.313,0.198 10 *b 4.417,1.833 4.75,2.083 0.333,0.25 10 *b 1.75,1.25 2.063,1.448 0.313,0.198 10 *1 2.583,1.25 3.083,1.448 0.5,0.198 10 *2 (*c) 5.25,1.188 5.698,1.417 0.448,0.229 10 *2 (*c) 6.74,0.083 7.052,0.281 0.313,0.198 10 *1 6.417,1.25 6.729,1.448 0.313,0.198 10 *1 1.667,2.51 1.979,2.708 0.313,0.198 10 *1 2.75,2.563 3.25,2.75 0.5,0.188 10 *2 (*d) 5.333,2.5 5.833,2.75 0.5,0.25 10 *2 (*d)
*1 Connector Housing *2 Terminal Housing
*a Incorrect *b Correct
*c Lock Position *d Unlock Position



ii.

Connect the sensor connector (yellow colored) to the front airbag sensor.

H103034C01
2.177,0.75 2.333,0.333 2.333,0.333 2.594,0.333 false 2.375,0.833 2.563,0.583 2.563,0.583 2.896,0.583 false 1.083,1.167 1.333,1.167 1.333,1.167 1.469,0.854 false 0.49,2.438 0.667,2 0.667,2 0.917,2 false 1.083,3.302 1.083,3.469 false 1.583,3.167 1.583,3.5 true 5.448,2.448 5.51,2.052 5.51,2.052 5.844,2.052 false 6.167,3.292 6.167,3.542 false 6.594,3.167 6.594,3.5 true 5.417,1.177 5.417,1.417 true 5.271,0.635 5.417,0.333 5.417,0.333 5.75,0.333 false 2.417,1.302 2.417,1.667 true 5.823,0.24 6.135,0.438 0.313,0.198 10 *2 2.677,0.24 2.833,0.438 0.156,0.198 10 A 2.979,0.5 3.292,0.698 0.313,0.198 10 *2 5.25,1.5 5.75,1.667 0.5,0.167 10 *1 (*a) 5.958,1.979 6.271,2.177 0.313,0.198 10 *3 6.417,3.542 7,3.75 0.583,0.208 10 *1 (*a) 6.031,3.552 6.344,3.75 0.313,0.198 10 *2 0.833,1.083 1.146,1.281 0.313,0.198 10 *3 2.365,1.74 2.677,1.938 0.313,0.198 10 *1 1,1.917 1.313,2.115 0.313,0.198 10 *3 1.021,3.5 1.333,3.698 0.313,0.198 10 *2 1.521,3.552 1.833,3.75 0.313,0.198 10 *1
*1 Terminal Housing *2 Connector Housing
*3 Front Airbag Sensor - -
*a Lock Position - -


NOTICE:
·

Do not push the part of the connector housing labeled A when connecting the sensor connector.

·

When handling the sensor connector, take care not to damage the sensor wire harness.




iii.

Check that the terminal housing is in the lock position.



d.

Install the front airbag sensor with the 2 bolts.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


e.

Check that the front airbag sensor assembly is not loose.


Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).