Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (Using SST Check Wire)


a.

Check for DTCs (present trouble code).

i.
C198509C03
1.813,1.5 2,1.771 true 1.635,0.885 2.021,0.49 true 1.5,0.146 1.729,0.365 0.229,0.219 10 *a 2.063,1.75 2.5,1.969 0.438,0.219 10 ECUT 2.073,0.417 2.302,0.635 0.229,0.219 10 E
*a Front view of DLC3


Turn the ignition switch to ON and wait for approximately 60 seconds.


ii.

Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  

NOTICE:

Connect the correct terminals to avoid a malfunction.




b.

Check for DTCs (past trouble code).

i.

Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  

NOTICE:

Connect the correct terminals to avoid a malfunction.



ii.

Turn the ignition switch to ON and wait for approximately 60 seconds.



c.
C271020E01
0.083,0.083 3.198,0.354 3.115,0.271 10 Normal System Code (without Past Trouble Code): 1.01,0.448 2.385,0.646 1.375,0.198 10 0.25 sec. 1.135,1.198 2.51,1.396 1.375,0.198 10 0.25 sec. 1.417,2.677 2.792,2.875 1.375,0.198 10 0.25 sec. 0.969,3.167 1.531,3.354 0.563,0.188 10 2.5 sec. 0.083,1.583 3.042,1.781 2.958,0.198 10 Normal System Code (with Past Trouble Code): 0.094,2.917 2.708,3.083 2.615,0.167 10 Trouble Code (Example Codes 11 and 31): 0.25,0.625 0.563,0.823 0.313,0.198 10 On 0.24,2.094 0.552,2.292 0.313,0.198 10 On 0.26,1.052 0.719,1.25 0.458,0.198 10 Off 0.25,2.552 0.708,2.75 0.458,0.198 10 Off 1.208,1.896 2.583,2.094 1.375,0.198 10 0.75 sec. 2.01,3.167 2.583,3.396 0.573,0.229 10 4.0 sec. 0.052,3.354 0.594,3.583 0.542,0.229 10 0.5 sec. 0.135,3.969 0.76,4.135 0.625,0.167 10 1.5 sec. 1.677,3.979 2.25,4.198 0.573,0.219 10 0.5 sec. 2.51,4.167 3.427,4.365 0.917,0.198 10 Repeat 0.646,4.438 1.188,4.625 0.542,0.188 10 DTC 11 1.438,4.438 1.99,4.615 0.552,0.177 10 DTC 31

Read the DTCs.

i.

Read the blinking patterns of the DTCs. As examples, the blinking patterns for the normal system code and trouble codes 11 and 31 are shown in the illustration.

·

Normal system code indication (without past trouble code):

The light blinks twice per second.

·

Normal system code indication (with past trouble code):

When a past trouble code is stored in the center airbag sensor, the light blinks only once per second.

·

Trouble code indication:

Each digit of a DTC is separated by a 1.5 second pause.


If there is more than 1 code, there is a 2.5 second pause between each code. After all the codes are output, there is a 4.0 second pause, and then all codes are repeated.

HINT:
·

If 2 or more malfunctions are found, the indication begins with the smaller-numbered code.

·

If DTCs are output without connecting the terminals, proceed to "Diagnosis Circuit" (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>Diagnosis Circuit).






DTC CLEAR (USING SST CHECK WIRE)


a.

Clear the DTCs. (method by using the ignition switch)

C141247E03
2.948,2.698 2.948,3.021 false 5.302,2.708 5.302,3.031 false 2.99,4.021 2.99,4.208 false 1.594,0.292 1.417,0.729 false 0.938,0.042 1.219,0.219 0.281,0.177 10 ON 0.198,0.135 0.708,0.49 0.51,0.354 10 Ignition Switch 0.927,0.396 1.292,0.583 0.365,0.188 10 OFF 2.25,4.24 3.771,4.427 1.521,0.188 10 Clear Completion Code 5.177,4.083 6.177,4.458 1,0.375 10 Code 21 (Trouble Code) 3.635,1.469 4.979,1.865 1.344,0.396 10 Normal Primar Check Confirmation 1.813,2.802 2.458,2.958 0.646,0.156 10 0.05 sec. 2.271,3.031 3.792,3.219 1.521,0.188 10 Clear Completion Code 4.135,2.802 4.75,3 0.615,0.198 10 0.25 sec. 4.99,3.031 6.354,3.26 1.365,0.229 10 Normal System Code 2.594,1.75 3.552,2.146 0.958,0.396 10 Code Clear Confirmation 5.104,1.729 6.354,2.094 1.25,0.365 10 Normal System Code Confirmation 1.625,0.198 3.198,0.583 1.573,0.385 10 6.0 sec. or more after turning ignition switch on 0.823,0.865 1.219,1.104 0.396,0.24 10 Open 0.823,1.135 1.396,1.51 0.573,0.375 10 Short to Ground 1.875,1.479 2.833,1.677 0.958,0.198 10 1.0 +/- 0.4 sec. 4.042,2.469 4.563,2.635 0.521,0.167 10 1.5 sec. 3.917,0.271 5.01,0.51 1.094,0.24 10 1.0 sec. or more 4.042,1.99 4.583,2.219 0.542,0.229 10 6.0 sec. 4.75,3.417 5.271,3.656 0.521,0.24 10 4.0 sec. 0.969,2.104 1.406,2.427 0.438,0.323 10 Hi (ON) 0.958,2.563 1.406,2.938 0.448,0.375 10 Lo (OFF) 0.094,2.177 0.906,2.698 0.813,0.521 10 Terminal LA Voltage (Normal) 0.094,3.594 0.906,4.115 0.813,0.521 10 Terminal LA Voltage (Abnormal) 0.969,3.427 1.406,3.75 0.438,0.323 10 Hi (ON) 0.958,3.875 1.406,4.25 0.448,0.375 10 Lo (OFF) 0.125,0.969 0.698,1.333 0.573,0.365 10 Terminal ECUT

i.

Connect the SST service wire to terminal ECUT of the DLC3.

SST
09843-18040  


ii.
C093955

Turn the ignition to ON and wait for at least 6 seconds.


iii.

Make terminal ECUT of the DLC3 open for 1 second, then short it to the ground for another 1 second.


iv.

Perform step (3) again.


v.

The SRS warning light blinks at 0.05 second intervals (Clear completion code is output).


vi.

Turn the ignition switch to Lock after the clear completion code is output and wait for at least 1 second.


vii.

Turn the ignition switch to ON and wait for at least 6 seconds (Primary check occurs during this period).


viii.

When the SRS warning system is determined to be normal by the primary and constant checks, and DTCs are cleared, the SRS warning light blinks at 0.25 second intervals (normal system code output) after the primary check ends.


ix.

Relevant DTCs are output approximately 4 seconds after the primary check ends if there is any trouble in the system. In this case, repair the trouble and perform the above procedure from step (3) to (8) again.



b.

Clear the DTCs. (method by using terminal ECUT of the DLC3)

C141248E03
2.938,2.833 2.938,3.156 false 4.344,2.823 4.344,3.146 false 2.969,4.146 2.969,4.333 false 1.594,0.417 1.427,0.854 false 0.927,0.177 1.208,0.354 0.281,0.177 10 ON 0.115,0.313 0.625,0.667 0.51,0.354 10 Ignition Switch 0.917,0.573 1.281,0.76 0.365,0.188 10 OFF 2.24,4.365 3.76,4.552 1.521,0.188 10 Clear Completion Code 4.073,4.188 5.073,4.563 1,0.375 10 Code 21 (Trouble Code) 5.646,1.469 6.958,1.865 1.313,0.396 10 Normal Primary Check Confirmation 1.792,2.938 2.438,3.094 0.646,0.156 10 0.05 sec. 2.24,3.208 3.76,3.396 1.521,0.188 10 Clear Completion Code 3,2.938 3.615,3.135 0.615,0.198 10 0.25 sec. 4.052,3.188 5.417,3.417 1.365,0.229 10 Normal System Code 5.927,2.49 6.625,2.885 0.698,0.396 10 Normal Operation 2.583,1.844 3.521,2.24 0.938,0.396 10 Code Clear Confirmation 3.76,1.854 4.99,2.219 1.229,0.365 10 Normal System Code Confirmation 1.625,0.333 3.49,0.719 1.865,0.385 10 6.0 sec. or more after turning ignition switch on 3.833,0.781 4.927,1.021 1.094,0.24 10 1.0 sec. or more 0.802,0.99 1.198,1.229 0.396,0.24 10 Open 0.802,1.281 1.375,1.656 0.573,0.375 10 Short to Ground 1.865,1.594 2.823,1.792 0.958,0.198 10 1.0 +/- 0.4 sec. 4.042,1.594 4.563,1.76 0.521,0.167 10 1.5 sec. 4.292,0.406 5.385,0.646 1.094,0.24 10 1.0 sec. or more 5.969,2.104 6.51,2.333 0.542,0.229 10 6.0 sec. 3.646,3.563 4.167,3.802 0.521,0.24 10 4.0 sec. 5.948,3.813 6.635,4.271 0.688,0.458 10 Abnormal Operation 0.958,2.24 1.396,2.563 0.438,0.323 10 Hi (ON) 0.938,2.677 1.385,3.052 0.448,0.375 10 Lo (OFF) 0.083,2.365 0.896,2.885 0.813,0.521 10 Terminal LA Voltage (Normal) 0.083,3.688 0.896,4.208 0.813,0.521 10 Terminal LA Voltage (Abnormal) 0.958,3.563 1.396,3.885 0.438,0.323 10 Hi (ON) 0.938,4.01 1.385,4.385 0.448,0.375 10 Lo (OFF) 0.104,1.063 0.677,1.427 0.573,0.365 10 Terminal ECUT

i.

Connect the SST service wire to terminal ECUT of the DLC3.

SST
09843-18040  


ii.

Turn the ignition to ON and wait for at least 6 seconds.


iii.

Make terminal ECUT of the DLC3 open for 1 second, then short it to the ground for another 1 second.


iv.

Perform step (3) again.


v.

The SRS warning light blinks at 0.05 second intervals (Clear completion code is output).


vi.

Make terminal ECUT of the DLC3 open after the clear completion code is output and wait for at least 1 second.


vii.

The SRS warning light blinks at 0.25 second intervals (normal system code output) approximately 1.5 seconds after making terminal ECUT open.


viii.

Relevant DTCs are output approximately 4 seconds after making terminal ECUT open for 1 second or more after the clear completion code is output if there is any trouble in the system. In this case, repair the trouble and perform the above procedure from step (3) to (7) again.




CHECK DTC (Using the Intelligent Tester or Techstream)


a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Body / SRS Airbag / Trouble Codes.

Body Electrical > SRS Airbag > Trouble Codes
50001 102


CLEAR DTC (Using the Intelligent Tester or Techstream)


a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Body / SRS Airbag / Trouble Codes.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

e.

Clear the DTCs.