Wear protective gloves. Sharp surfaces on the front seat frame assembly with adjuster could cause injuries to your hands.
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
71329A
1.INSTALL FRONT SEAT CUSHION REINFORCE SUB-ASSEMBLY
Install the front seat cushion reinforce sub-assembly with the bolt and nut.
71831D
2.INSTALL FRONT SEAT HINGE COVER
Engage the 2 claws and guide and install the front seat hinge cover.
71521
3.INSTALL FRONT SEAT CUSHION SILENCER PAD
Install the front seat cushion silencer pad to the separate type front seat cushion pad.
71511S
4.INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD
Install the separate type front seat cushion pad to the front seat frame assembly with adjuster.
71071S
5.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 3 new hog rings.
Do not soil or scratch the separate type front seat cushion cover.
When installing the hog rings, minimize wrinkles as much as possible.
Attach the 4 hooks.
Install the 2 clips.
72110A
6.INSTALL FRONT SEAT OUTER TRACK ASSEMBLY
Install the front seat outer track assembly with the 2 bolts.
72130A
7.INSTALL FRONT SEAT INNER TRACK ASSEMBLY
Use the same procedure as for the front seat outer track assembly.
72211
8.INSTALL SEAT TRACK ADJUSTING HANDLE
| *1 | Spring |
Insert the seat track adjusting handle in the direction indicated by the arrow in the illustration.
Engage the 2 springs to install the seat track adjusting handle.
72991
9.INSTALL FRONT SEAT CUSHION COVER RH
Engage the 2 claws and install the front seat cushion cover RH.
72992
10.INSTALL FRONT SEAT CUSHION COVER LH
Use the same procedure as for the RH side.
71537C
11.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR
Engage the 8 claws and install the 4 front seat cushion edge protectors.
72137B
12.INSTALL SEAT TRACK COVER
Engage the 8 claws and install the 2 front seat track covers.
71571
13.INSTALL FRONT SEAT BACK SILENCER PAD
Install the front seat back silencer pad to the separate type front seat back pad.
71551S
14.INSTALL SEPARATE TYPE FRONT SEAT BACK PAD
Install the separate type front seat back pad to the front seat frame assembly with adjuster.
71073S
15.INSTALL SEPARATE TYPE FRONT SEAT BACK COVER
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat back cover to the separate type front seat back pad with 3 new hog rings.
Do not soil or scratch the separate type front seat back cover.
When installing the hog rings, minimize wrinkles as much as possible.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install 3 new hog rings.
Do not soil or scratch the separate type front seat back cover.
When installing the hog rings, minimize wrinkles as much as possible.
Attach the hook
| *1 | Rubber Band |
Put the 2 rubber bands on the front seat frame assembly with adjuster.
71931
16.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
| *1 | Protruding Portion |
Align the protruding portion of the front seat headrest support assembly with the installation groove of the front seat frame assembly with adjuster.
Engage the 2 claws and install the front seat headrest support assembly.
71931
17.INSTALL FRONT SEAT HEADREST SUPPORT
| *1 | Protruding Portion |
Align the protruding portion of the front seat headrest support with the installation groove of the front seat frame assembly with adjuster.
Engage the 2 claws and install the front seat headrest support.
71811D
18.INSTALL FRONT SEAT CUSHION SHIELD
Install the front seat cushion shield with the 2 screws.
73230
19.INSTALL FRONT SEAT INNER BELT ASSEMBLY (w/o Seat Belt Warning System)
73230
20.INSTALL FRONT SEAT INNER BELT ASSEMBLY (w/ Seat Belt Warning System)
72525A
21.INSTALL RECLINING ADJUSTER RELEASE HANDLE
| *1 | New Snap Ring |
Install the reclining adjuster release handle with a new snap ring.