Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0015227 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 87107A 1.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (w/ Heater)

a.
E238933

Install the heater radiator unit sub-assembly.


b.
E237593

Install the bolt.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88304A 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for RHD)

a.

w/o Heater:

i.
E238934

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new cooler evaporator sub-assembly is installed, add compressor oil to the cooler evaporator sub-assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



ii.

Engage each claw and install the upper heater case.


iii.

Install the blower case.


iv.

Install the 21 screws.

E231839


v.
E231842

Engage the No. 1 cooler thermistor connector clamp.



b.

w/ Heater:

i.
E238934

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new cooler evaporator sub-assembly is installed, add compressor oil to the cooler evaporator sub-assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



ii.
E237826

Install the upper case.


iii.
E238931

Install the blower case.


iv.

Install the 25 screws.

E237591


v.
E231842

Engage the No. 1 cooler thermistor connector clamp.



Hide 88304A 4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for LHD)

a.
E238934

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new cooler evaporator sub-assembly is installed, add compressor oil to the cooler evaporator sub-assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



b.
E237826

Install the upper case.


c.
E238931

Install the blower case.


d.

Install the 28 screws.

E237592


e.
E231842

Engage the No. 1 cooler thermistor connector clamp.


Hide 88539J 5.INSTALL DRAIN COOLER HOSE

a.
E231793

Install the drain cooler hose.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88515 6.INSTALL COOLER EXPANSION VALVE

a.
E231841

Apply sufficient compressor oil to new 2 O-rings and the fitting surfaces of the cooler expansion valve.

Compressor oil:

ND-OIL8 or equivalent



b.

Install the 2 O-rings onto the No. 1 cooler evaporator sub-assembly.


c.

Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88521B 7.INSTALL COOLER UNIT CASE PACKING

a.
E231838

Install the new cooler unit packing.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88504A 10.INSTALL BLOWER CASE SUB-ASSEMBLY

a.
E237590

Engage the 5 claws and install the blower case sub-assembly.

HINT:

Use the same procedure for the RHD and LHD vehicle.