Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for K3-VE) › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0015231 COMPRESSOR(for K3-VE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for K3-VE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the cooler compressor assembly with a new one, gradually release the refrigerant gas from the service valve and drain the following amount of oil from the new compressor before installation.

Standard:

(Oil capacity inside the new compressor: 80 to 95 cc (2.7 to 3.2 fl. oz.)) - (Remaining oil amount in the removed compressor) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

Since compressor oil remains in the pipes of the vehicle, if a new cooler compressor assembly is installed without removing some oil from the cooler compressor assembly, the oil amount becomes excessive. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed cooler compressor assembly is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
E231781N01
2.781,1.578 2.882,1.759 0.101,0.181 10 1 2.505,1.825 2.606,2.006 0.101,0.181 10 2 2.103,1.916 2.203,2.097 0.101,0.181 10 3 2.617,1.118 2.718,1.299 0.101,0.181 10 4

for RHD:

i.

Install the cooler compressor assembly with the 4 bolts and 3 cooler brackets.

Torque:
26 N*m (269 kgf*cm, 20 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.




b.
E238737N01
2.771,1.604 3.104,1.927 0.333,0.323 10 1 2.104,1.948 2.458,2.177 0.354,0.229 10 3 2.51,1.813 2.865,2.167 0.354,0.354 10 2 2.646,1.125 2.99,1.427 0.344,0.302 10 4

for LHD:

i.

Install the cooler compressor assembly with the 4 bolts.

Torque:
26 N*m (269 kgf*cm, 20 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.




Hide 88712D 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant suction hose.


d.

Connect the No. 1 cooler refrigerant suction hose to the cooler compressor with the bolt.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor assembly with the bolt.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 7. WARM UP ENGINE