Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › 2011.11–2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015255 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RHD and LHD vehicle.


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS SUB-ASSEMBLY

a.
B112214

Using a scraper, remove any excess or protruding adhesive sticking to the back door glass sub-assembly.

NOTICE:

Be careful not to damage the glass.



b.

Clean the outer surface of the back door glass sub-assembly with a non-residue solvent.

NOTICE:

Even if using a new back door glass sub-assembly, clean the back door glass sub-assembly with a non-residue solvent.



Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP LH

B291366

a.

Apply primer G to the installation part of the back window glass clip LH.

NOTICE:

Do not apply too much primer G.



b.

Install new back window glass clip LH onto the back door glass sub-assembly, as shown in the illustration.

NOTICE:

Allow the primer G to dry for 3 minutes or more.



Hide 64827A 3.INSTALL BACK WINDOW GLASS CLIP RH

B289337

a.

Apply primer G to the installation part of the back window glass clip RH.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.




b.

Install new back window glass clip RH onto the back door glass sub-assembly, as shown in the illustration.


Hide 64818B 4.INSTALL BACK DOOR GLASS SPACER

a.

Apply primer M to the installation part of the back window glass spacer.

NOTICE:

Do not apply too much primer M.



b.

Install new quarter window glass spacer onto the back door panel sub-assembly, as shown in the illustration.

B289338C02
0.688,0.823 1.146,1.396 0.458,0.573 10 a 6.448,0.802 6.917,1.24 0.469,0.438 10 a 6.427,3.542 6.906,3.979 0.479,0.438 10 a 5.865,3.615 6.365,4.021 0.5,0.406 10 a 1.302,3.604 1.802,4.031 0.5,0.427 10 a 0.781,3.531 1.323,4.052 0.542,0.521 10 a 1.396,0.771 1.875,1.188 0.479,0.417 10 a 5.74,0.771 6.24,1.25 0.5,0.479 10 a 3.229,1.021 3.667,1.438 0.438,0.417 10 a 3.927,1.031 4.281,1.396 0.354,0.365 10 a 3.229,4.323 3.677,4.74 0.448,0.417 10 a 3.927,4.323 4.552,4.802 0.625,0.479 10 a
V100145

Back Window Glass Spacer - -


Standard Dimension:
Area Dimension
a 2.5 mm (0.0981 in.)


NOTICE:

Allow the primer M to dry for 3 minutes or more.



Hide 68131 5.INSTALL BACK DOOR GLASS SUB-ASSEMBLY

B221174C05
3.063,2.083 3.292,2.083 false
V100155

Adhesive


a.

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the outer edge of the back door glass sub-assembly with a non-residue solvent.



b.
B295410C05
0.994,0.078 1.236,0.27 0.243,0.192 10 *a 2.524,0.078 2.766,0.27 0.243,0.192 10 *b
*a NG
*b OK
V100145

Primer M
V100155

Adhesive


Using a brush, apply primer M to the exposed part of the vehicle body.

NOTICE:
·

Do not apply primer M to the adhesive.

·

Throw away any leftover primer M.

·

Do not apply too much primer M.




c.

Using a brush, apply primer G to the contact surface.

B323665C02
0.198,0.135 0.792,0.646 0.594,0.51 10 *a 1.417,1.313 2.01,1.823 0.594,0.51 10 A 1.417,1.719 2.01,2.229 0.594,0.51 10 A 1.438,2.24 1.948,2.583 0.51,0.344 10 B 1.438,2.646 1.948,2.99 0.51,0.344 10 B 0.667,1.479 1.177,1.823 0.51,0.344 10 C 0.24,1.365 0.75,1.708 0.51,0.344 10 C 3.823,0.375 4.448,0.708 0.625,0.333 10 C - C 5.542,0.375 6.167,0.708 0.625,0.333 10 A - A 5.563,2 6.188,2.333 0.625,0.333 10 B - B 4.646,0.688 5,1.031 0.354,0.344 10 b 4.281,1.396 4.635,1.74 0.354,0.344 10 e 6.51,0.74 6.865,1.083 0.354,0.344 10 c 5.979,1.313 6.333,1.656 0.354,0.344 10 a 5.844,2.792 6.198,3.135 0.354,0.344 10 a 6.594,2.531 6.948,2.875 0.354,0.344 10 d
*a Back Side - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 15.0 mm (0.590 in.)
b 23.0 mm (0.905 in.)
c 24.5 mm (0.964 in.)
d 28.5 mm (1.122 in.)
e 32.5 mm (1.279 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.



i.

Cut off the tip of the cartridge nozzle as shown in the illustration.


ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass sub-assembly as shown in the illustration.

B323666C02
3.063,0.792 2.698,1.031 true 4.375,2.698 4.885,2.667 true 5.979,3.042 6.083,2.719 true 6.219,0.896 6.698,0.823 6.698,0.823 6.365,0.948 true 0.156,0.094 0.656,0.5 0.5,0.406 10 *a 0.229,1.375 0.635,1.656 0.406,0.281 10 C 0.646,1.469 1.052,1.75 0.406,0.281 10 C 1.448,1.302 1.854,1.583 0.406,0.281 10 A 1.438,1.698 1.844,1.979 0.406,0.281 10 A 1.417,2.208 1.823,2.49 0.406,0.281 10 B 1.417,2.625 1.823,2.906 0.406,0.281 10 B 2.531,1.042 3.104,1.427 0.573,0.385 10 *1 4.104,0.969 4.51,1.25 0.406,0.281 10 a 4.375,0.625 4.781,0.906 0.406,0.281 10 b 4.844,0.854 5.25,1.135 0.406,0.281 10 a 3.854,1.938 4.552,2.333 0.698,0.396 10 A - A 4.573,1.354 4.979,1.635 0.406,0.281 10 b 4.656,2.146 5.063,2.427 0.406,0.281 10 c 4.979,2.583 5.385,2.865 0.406,0.281 10 *b 5.854,3.073 6.26,3.354 0.406,0.281 10 *b 5.552,1.958 6.25,2.354 0.698,0.396 10 B - B 5.563,0.354 6.26,0.75 0.698,0.396 10 C - C 6.635,2.542 6.948,2.813 0.313,0.271 10 d 6.75,0.729 7.156,1.01 0.406,0.281 10 *b 5.948,1 6.354,1.281 0.406,0.281 10 c 6.063,1.323 6.469,1.604 0.406,0.281 10 a
*1 Sealer Gun - -
*a Back Side *b Adhesive Center Line
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.275 in.)
b 12.0 mm (0.472 in.)
c 17.0 mm (0.669 in.)
d 21.0 mm (0.826 in.)




d.

Install the back door glass sub-assembly.

i.

Using suction cups, position the back door glass sub-assembly so that the matchmarks are aligned. Press it in gently along the rim.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and back door glass sub-assembly have a small gap between them.




ii.

Gently press the front surface of the back door glass sub-assembly to ensure that the back door glass is securely fitted to the vehicle body.


iii.

Hold the back door glass sub-assembly in place securely with protective tape or equivalent until the adhesive hardens.


iv.
B159610C10
0.688,1.26 0.375,0.74 false 2.26,1.302 1.927,0.76 false 0.188,0.646 0.698,0.99 0.51,0.344 10 *1 1.75,0.656 2.208,0.958 0.458,0.302 10 *1
*1 Adhesive


Using a scraper, remove any excess or protruding adhesive.


v.

Hold the windshield glass using protective tape until applied adhesive becomes hard.



e.

Connect the 2 connectors. (w/ Rear Defogger)


Hide 76871 7.INSTALL REAR SPOILER (w/ Rear Spoiler)