Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Front Door)
RM19Y0E _59 Vehicle Exterior _003022 EXTERIOR PANELS / TRIM _0015305 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

When installing the black out tape, heat the vehicle body surface and black out tape using a heat light.


Heating Temperature:
Item Temperature
Vehicle Body 15 to 25°C (59 to 77°F)
Black Out Tape 15 to 25°C (59 to 77°F)


NOTICE:

Do not heat the vehicle body or black out tape excessively.


PROCEDURE

Hide 1.REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 40 and 60°C (104 and 140°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for flat surfaces).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

B147252C03
0.083,0.073 3.875,1.563 3.792,1.49 2,2.281 1.5,2.646 true 1.865,3.083 1.396,3.083 true 2.135,2 2.135,1.833 2.135,1.833 2.594,1.833 true 2.094,3.427 2.646,3.427 true 4.542,2.677 4.938,2.677 true 4.865,3.052 5.292,3.052 true 5.708,2.646 5.948,2.99 5.948,2.99 6.063,2.99 true 5.677,3.26 6.073,3.26 true 2.104,1.198 2.438,1.323 true 2.188,0.729 2.531,0.479 true 3.885,0.781 4.302,0.781 false 4.344,0.719 4.708,1.031 0.365,0.313 10 *1 4.677,2.979 5.052,3.313 0.375,0.333 10 *2 0.167,0.135 0.521,0.458 0.354,0.323 10 *a 1.302,2.563 1.76,2.969 0.458,0.406 10 *1 4.354,2.604 4.75,2.927 0.396,0.323 10 *1 2.542,0.365 2.938,0.698 0.396,0.333 10 *b 2.458,1.292 2.813,1.583 0.354,0.292 10 *c 3.948,1.635 4.323,2.01 0.375,0.375 10 *g 0.24,1.635 0.646,2.042 0.406,0.406 10 *d 1.219,3.01 1.604,3.375 0.385,0.365 10 *2 2.677,3.365 3.094,3.677 0.417,0.313 10 *3 6.115,3.188 6.458,3.51 0.344,0.323 10 *3 6.323,2.208 6.677,2.531 0.354,0.323 10 *f 2.813,2.552 3.167,2.906 0.354,0.354 10 *f 2.635,1.729 3.01,2.052 0.375,0.323 10 *e 6.104,2.917 6.521,3.24 0.417,0.323 10 *h
*1 Squeegee *2 Black Out Tape
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side *d For pressing forward
*e 40 to 50° *f 10 to 20 mm (0.393 to 0.787 in.)
*g For pulling *h 30 to 45°
V100136

3 to 7 cm (1.2 to 2.8 in.)/sec. - -


NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.





f.
B147253C04
1.177,1.646 0.615,1.646 true 2.438,0.5 2.792,0.781 0.354,0.281 10 *a 1.802,0.302 2.156,0.604 0.354,0.302 10 *b 0.885,0.406 1.24,0.708 0.354,0.302 10 *c 0.458,1.563 0.802,1.896 0.344,0.333 10 *1
*1 Squeegee
*a First
*b Second
*c Third


Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75956B 2.INSTALL FRONT DOOR UPPER OUTER BLACK OUT TAPE

a.

Refer to the illustration to position a new front door upper outer black out tape.

B270479N02
2.115,0.969 2.438,1.25 0.323,0.281 10 A 4.875,0.729 5.448,1.042 0.573,0.313 10 A - A 2.406,1.469 2.677,1.76 0.271,0.292 10 A 6.094,0.896 6.385,1.24 0.292,0.344 10 a 6.5,1.646 6.823,1.948 0.323,0.302 10 b

Standard Measurement:
Dimension Measurement
a 2 to 4 mm (0.078 to 0.157 in.)
b 4 to 6 mm (0.157 to 0.236 in.)


HINT:

The cutout section distinguishes between the left and right sides, so be sure that the right-and-left orientation is correct, as shown in the illustration.



b.

Remove the release paper and apply the tape.


Hide 75958B 3.INSTALL FRONT DOOR REAR OUTER BLACK OUT TAPE

a.

Refer to the illustration to position a new front door rear outer black out tape.

B270480N02
2.563,1.188 2.938,1.604 true 2.573,2.354 2.885,2.604 0.313,0.25 10 B 3.177,2.375 3.469,2.635 0.292,0.26 10 B 3.115,2.542 3.427,2.802 0.313,0.26 10 C 3.094,2.885 3.438,3.229 0.344,0.344 10 C 4.177,0.094 4.573,0.396 0.396,0.302 10 A 4.104,1.24 4.615,1.583 0.51,0.344 10 B - B 4.104,3.052 4.688,3.427 0.583,0.375 10 C - C 5.167,1.01 5.531,1.333 0.365,0.323 10 a 4.74,1.448 5.063,1.771 0.323,0.323 10 b 6.208,1.448 6.573,1.75 0.365,0.302 10 c 2.396,1.042 2.771,1.375 0.375,0.333 10 A

Standard Measurement:
Dimension Measurement
a 2 to 4 mm (0.078 to 0.157 in.)
b 4 to 6 mm (0.157 to 0.236 in.)
c 2 to 4 mm (0.078 to 0.157 in.)



b.

Remove the release paper and apply the tape.


Hide 67862 4.INSTALL FRONT DOOR WEATHERSTRIP

Hide 68210C 5.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68151E 6.INSTALL FRONT DOOR GLASS RUN

Hide 68102 7.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 8.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 86160 9.INSTALL FRONT DOOR SPEAKER

Hide 69206B 10.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

Hide 67601 11.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74640C 12.INSTALL DOOR ASSIST GRIP ASSEMBLY

Hide 87910 13.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67492A 14.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH