Wear protective gloves. Sharp surfaces on the front seat frame with adjuster assembly could cause injuries to your hands.
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
72137B
1.INSTALL SEAT TRACK COVER
Engage the 8 claws to install the 2 seat track covers.
71537C
2.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR
Engage the 8 claws to install the 4 front seat cushion edge protectors.
72110A
3.INSTALL FRONT SEAT OUTER TRACK ASSEMBLY
Install the front seat outer track assembly with the 2 bolts.
72130A
4.INSTALL FRONT SEAT INNER TRACK ASSEMBLY
Use the same procedure as for the front seat outer track assembly.
71139A
5.INSTALL FRONT SEAT LEG COVER
Engage the claw to install the front seat leg cover with the screw.
6.INSTALL SEAT BELT HANGER BRACKET (w/ Seat Belt Warning System)
Install the seat belt hanger bracket with the screw.
71430C
7.INSTALL GROMMET
Engage the 4 claws to install the 2 grommets.
71121
8.INSTALL FRONT SEAT CUSHION BRACKET
Install the front seat cushion bracket with the 2 nuts.
71329A
9.INSTALL FRONT SEAT CUSHION REINFORCE SUB-ASSEMBLY
Install the front seat cushion reinforce sub-assembly with the bolt and nut.
71127A
10.INSTALL FRONT SEAT CUSHION COVER SET PLATE
Use the same procedure for both sides.
Install the front seat cushion cover set plate with the screw.
72211
11.INSTALL SEAT TRACK ADJUSTING HANDLE
| *1 | Spring |
Insert the seat track adjusting handle in the direction indicated by the arrow in the illustration.
Engage the 2 springs to install the seat track adjusting handle.
72991
12.INSTALL FRONT SEAT CUSHION COVER RH
Engage the 2 claws to install the front seat cushion cover RH.
72992
13.INSTALL FRONT SEAT CUSHION COVER LH
Use the same procedure as for the RH side.
71831D
14.INSTALL FRONT SEAT HINGE COVER
Engage the 2 claws and guide to install the front seat hinge cover.
71521
15.INSTALL FRONT SEAT CUSHION SILENCER PAD
Install the front seat cushion silencer pad to the separate type front seat cushion pad.
71511S
16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD
Install the separate type front seat cushion pad to the front seat frame with adjuster assembly.
71071S
17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 11 new hog rings.
Do not soil or scratch the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Attach the 4 hooks.
Install the 2 clips.
73230
18.INSTALL FRONT SEAT INNER BELT ASSEMBLY (w/ Seat Belt Warning System)
73230
19.INSTALL FRONT SEAT INNER BELT ASSEMBLY (w/o Seat Belt Warning System)
71811D
20.INSTALL FRONT SEAT CUSHION SHIELD
Install the front seat cushion shield with the clip.
Install the 2 screws.
72525A
21.INSTALL RECLINING ADJUSTER RELEASE HANDLE
| *1 | Snap Ring |
Install the reclining adjuster release handle with a new snap ring.
71571
22.INSTALL FRONT SEAT BACK SILENCER PAD
Install the front seat back silencer pad to the separate type front seat back pad.
71551S
23.INSTALL SEPARATE TYPE FRONT SEAT BACK PAD
Install the separate type front seat back pad to the front seat frame with adjuster assembly.
71073S
24.INSTALL SEPARATE TYPE FRONT SEAT BACK COVER
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat back cover to the separate type front seat back pad with 13 new hog rings.
Do not soil or scratch the separate type front seat back cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat back cover.
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Using hog ring pliers, install 2 new hog rings.
Do not soil or scratch the separate type front seat back cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat back cover.
Attach the hook.
Connect the 2 rubber bands on the front seat frame with adjuster assembly.
71931
25.INSTALL FRONT SEAT HEADREST SUPPORT
| *a | Protruding Portion |
Align the protruding portions of the front seat headrest support with the installation grooves of the front seat frame with adjuster assembly.
Engage the 2 claws to install the front seat headrest support.
71931
26.INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY
| *a | Protruding Portion |
Align the protruding portion of the front seat headrest support assembly with the installation groove of the front seat frame with adjuster assembly.
Engage the 2 claws to install the front seat headrest support assembly.