Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2013.07
RM19Y0E _59 Vehicle Exterior _003017 DOOR / HATCH _0015262 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


PROCEDURE

Hide 67001A 1.INSTALL FRONT DOOR PANEL CUSHION

a.
B297789

Install new 2 front door panel cushions.


Hide 67862 2.INSTALL FRONT DOOR WEATHERSTRIP

a.
B312477N01
0.708,1.969 1.031,2.198 0.323,0.229 10 A 1.198,2.208 1.521,2.438 0.323,0.229 10 C 1.208,2.573 1.531,2.802 0.323,0.229 10 C 1.25,2.792 1.573,3.021 0.323,0.229 10 C 1.271,3.229 1.594,3.458 0.323,0.229 10 C 1.865,2.885 2.188,3.115 0.323,0.229 10 C 2.125,2.802 2.448,3.031 0.323,0.229 10 C 2.573,3.135 2.896,3.365 0.323,0.229 10 C 2.958,2.906 3.281,3.135 0.323,0.229 10 C 2.979,2.625 3.302,2.854 0.323,0.229 10 C 2.958,2.375 3.281,2.604 0.323,0.229 10 C 3,2.177 3.323,2.406 0.323,0.229 10 C 3.021,1.906 3.344,2.135 0.323,0.229 10 C 2.875,1.365 3.198,1.594 0.323,0.229 10 B 1.583,3.406 1.906,3.635 0.323,0.229 10 C

Engage the 13 clips <C>.


b.

Engage the clip <A> and clip <B> to install the front door weatherstrip.


Hide 68620 3.INSTALL FRONT DOOR CHECK ASSEMBLY

a.
B297794C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the sliding areas of the front door check assembly.


b.
B297787

Install the front door check assembly onto the door panel with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Apply adhesive to the threads of the bolts (body side).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the front door check assembly onto the body panel with the bolt.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 69320 4.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 5.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B297835

Install the front door outside handle assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the control rod.


Hide 6.INSTALL HOLE PLUG

a.
B293723

Install a new hole plug.


Hide 69503 7.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY

a.
B149817

Install the front door lock cylinder assembly and door cylinder pad with the front door lock cylinder retainer.


b.
B149815

Connect the control rod.


Hide 67404F 8.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B297786

Engage the claw, and install the front door rear lower frame sub-assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 69802 9.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly.


b.
B297785C01
2.198,0.719 2.354,0.177 true 2.333,0.01 2.677,0.302 0.344,0.292 10 *1
*1 Temporary Bolt


Install the temporary bolt.


c.

Tighten the 5 bolts and temporary bolt to install the front door window regulator sub-assembly.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the connector.


Hide 68210C 10.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68151E 11.INSTALL FRONT DOOR GLASS RUN

a.
B297784

Install the front door glass run.


Hide 68102 12.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.
B297795N01
1.708,0.229 1.969,0.458 0.26,0.229 10 1 0.74,0.24 1.01,0.521 0.271,0.281 10 2

Insert the front door glass sub-assembly into the door panel along the glass run as indicated by the arrows in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly and body panel.



b.
B297782

Install the front door glass sub-assembly onto the front door window regulator sub-assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 87910 13.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67832 14.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B364852C01
0,0 0,0 false
V100145

Front Door Service Hole Cover
V100143

Butyl Tape


Apply new butyl tape to the door panel, then install new front door service hole cover as shown in the illustration.

HINT:
·

When installing the front door service hole cover, pull the cables out through service hole.

·

There should be no wrinkles or folds after attaching the front door service hole cover.

·

After attaching the front door service hole cover, check the quality of the seal.




Hide 69206B 16.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B297780C01
0.667,0.938 0.375,0.313 true 0.583,1.49 0.354,1.844 true 0.198,0.146 0.552,0.385 0.354,0.24 10 *1 0.156,1.833 0.542,2.083 0.385,0.25 10 *2
*1 Front Door Lock Remote Control Cable Assembly
*2 Front Door Inside Locking Cable Assembly


Connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.
B297853C02
1.222,1.355 1.378,1.536 0.156,0.182 10 *1 2.767,1.355 2.923,1.536 0.156,0.182 10 *2 2.655,1.701 2.795,1.503 false 1.034,1.685 1.248,1.498 false
*1 Claw
*2 Guide


Engage the 2 guides.


c.

Engage the claw and install the front door inside handle sub-assembly.


Hide 67602 17.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B297778

Engage the 7 clips and install the front door trim board sub-assembly.


b.

Tighten the 3 screws.


Hide 84820 18.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 84810 19.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 74640C 20.INSTALL DOOR ASSIST GRIP ASSEMBLY LH

a.
B297777

Engage the 9 claws and install the door assist grip assembly LH.


b.

Install the screw.


Hide 74630C 21.INSTALL DOOR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67492A 22.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B365123

Engage the 2 claws while sliding the front door lower frame bracket garnish down as shown in the illustration.


b.

Engage the clip and install the front door lower frame bracket garnish.


Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION