Home › Engine / Hybrid System › 3SZ-VE ENGINE MECHANICAL › CAMSHAFT › 2014.04–2015.08
RM19Y0E _51 Engine / Hybrid System _002969 3SZ-VE ENGINE MECHANICAL _0014994 CAMSHAFT A

3SZ-VE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 51441D 1.REMOVE ENGINE UNDER COVER (for Half Cover Type)

Hide 51441 2.REMOVE ENGINE UNDER COVER (for Full Cover Type)

Hide 51443 3.REMOVE REAR ENGINE UNDER COVER (for Full Cover Type)

Hide 22268 9.REMOVE NO. 2 THROTTLE BODY BRACKET

Hide 16507 11.SEPARATE RADIATOR PIPE SUB-ASSEMBLY

Hide 11201 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A285953N01
0.188,0.208 0.615,0.563 0.427,0.354 10 6 0.573,0.146 1,0.5 0.427,0.354 10 12 1.698,0.323 2.125,0.677 0.427,0.354 10 10 2.75,0.323 3.177,0.677 0.427,0.354 10 8 3.115,0.938 3.427,1.26 0.313,0.323 10 5 2.313,1.229 2.625,1.552 0.313,0.323 10 1 1.292,1.198 1.604,1.521 0.313,0.323 10 2 0.271,1.219 0.583,1.542 0.313,0.323 10 4 0.615,1.875 0.969,2.177 0.354,0.302 10 9 1.031,1.698 1.573,2.104 0.542,0.406 10 11 1.625,1.708 2.167,2.115 0.542,0.406 10 13 2.292,1.729 2.833,2.135 0.542,0.406 10 7 2.958,1.719 3.385,2.104 0.427,0.385 10 3

Remove the 11 bolts and 2 nuts in the sequence shown in the illustration, then remove the cylinder head cover sub-assembly.


Hide 11213 13.REMOVE CYLINDER HEAD COVER GASKET

Hide 11304 14.REMOVE NO. 2 TIMING CHAIN OR BELT COVER

a.
A130142

Remove the 2 bolts and No. 2 timing chain or belt cover.


Hide 13511 15.REMOVE CAMSHAFT

a.
A139287

Turn the crankshaft pulley clockwise and remove the 2 bolts.


b.
A130143

Turn the crankshaft clockwise to align the timing mark of the crankshaft pulley with the indicator of the timing chain cover.

NOTICE:

In order to prevent interference of the valve with the piston when removing the camshaft, turn the crankshaft clockwise by approximately 90° from the TDC/compression of the No. 1 cylinder.



c.
A130110C04
1.188,0.51 2.094,1.448 2.094,1.448 2.208,0.792 true 2.031,1.479 2.49,1.844 0.458,0.365 10 *a
*a Matchmark


Check that the matchmarks of the camshaft timing sprockets are facing upward. If not, turn the crankshaft 1 revolution so they face upward (No. 1 cylinder at TDC/compression).


d.
A130111C15
2.229,0.688 1.01,0.156 1.01,0.156 1.26,0.385 true 2.135,1.531 2.208,0.802 true 1.198,0.51 2.146,1.521 true 0.802,0.052 1.208,0.49 0.406,0.438 10 *a 2.083,1.542 2.51,1.917 0.427,0.375 10 *b
*a Paint Mark
*b Matchmark


Put 2 paint marks on the timing chain plates so that each of them is aligned with the matchmark on the camshaft timing sprocket and the matchmark on the camshaft timing gear.


e.
A130146

While holding the hexagonal lobe of the camshaft with a wrench, loosen the bolt which holds the camshaft timing sprocket.

NOTICE:

The bolt should be only loosened. Do not remove the bolt and sprocket.


HINT:

Loosen the bolt in advance. If the bolt is loosened after the chain is removed, the chain may interfere with the sprocket.



f.
A130147

Using a 10 mm socket hexagon wrench, remove the plug.


g.
A130148

Insert a screwdriver into the chain cover service hole, then move the stopper plate of the tensioner downward and keep it unlocked.

HINT:
·

This operation unlocks the plunger of the tensioner.

·

If the stopper plate is not unlocked easily, turn the camshaft right and left using the hexagonal lobe of the camshaft.




h.
A259476

Using the hexagonal lobe of the camshaft, slightly turn the camshaft to the right so the plunger of the tensioner is pushed by the chain.


i.
A137118

Remove the screwdriver from the chain cover service hole. Align the holes of the stopper plate and tensioner, and insert a 2.5 mm (0.098 in.) diameter hexagon wrench.

NOTICE:
·

Hold the camshaft using the hexagonal lobe of the camshaft.

·

Hold the 2.5 mm (0.098 in.) diameter hexagon wrench with tape so it is not pulled out.



HINT:

This operation keeps the plunger of the tensioner in place.



j.
A143162

Remove the fixing bolt of the camshaft timing gear or sprocket and remove the sprocket from the No. 2 camshaft.


k.
A143168

Remove the bolt and camshaft timing sprocket assembly.


l.

Remove the 20 bolts.


m.
A137120N03
0.427,1.625 0.198,1.854 true 0.438,1.333 0.177,1.323 true 0.469,1.01 0.188,1.01 true 0.469,0.604 0.188,0.51 true 0.813,1.594 0.844,1.969 true 1.385,1.604 1.313,1.958 true 2,1.594 2,1.969 true 2.573,1.594 2.573,1.969 true 2.583,0.177 2.583,0.708 true 2,0.156 2,0.688 true 1.406,0.146 1.406,0.708 true 0.844,0.156 0.844,0.688 true 0.094,1.781 0.5,2.104 0.406,0.323 10 1 0.073,1.25 0.417,1.594 0.344,0.344 10 3 0.063,0.938 0.396,1.333 0.333,0.396 10 4 0.083,0.438 0.5,0.771 0.417,0.333 10 2 0.802,1.979 1.177,2.177 0.375,0.198 10 6 1.281,1.979 1.667,2.146 0.385,0.167 10 8 1.969,1.979 2.302,2.146 0.333,0.167 10 5 2.542,1.979 2.906,2.177 0.365,0.198 10 7 2.51,0.01 2.906,0.281 0.396,0.271 10 11 1.917,0 2.323,0.281 0.406,0.281 10 12 1.365,0 1.677,0.292 0.313,0.292 10 9 0.75,0.01 1.167,0.271 0.417,0.26 10 10

Remove the No. 1 bearing cap and 8 No. 2 bearing caps in the sequence shown in the illustration.


n.

Hold the timing chain by hand, then remove the camshaft.


o.
A137121

After removing the camshaft, hold the chain by using a bar to prevent it from coming off.