17167
1.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17118
2.REMOVE MANIFOLD STAY
17141
3.REMOVE EXHAUST MANIFOLD
16261
4.DISCONNECT WATER BY-PASS HOSE (w/ Heater)
Disconnect the 2 water by-pass hose.
16261
5.DISCONNECT WATER BY-PASS HOSE (w/o Heater)
Disconnect the water by-pass hose.
16267
6.REMOVE NO. 3 WATER BY-PASS HOSE (w/ Heater)
Disconnect the fuel hose.
Disconnect the 2 No. 3 water by-pass hose.
7.REMOVE NO. 2 FUEL PIPE CLAMP
8.REMOVE FUEL TUBE SUB-ASSEMBLY
16322
9.REMOVE WATER INLET PIPE
Remove the 2 bolts.
Disconnect the water inlet pipe.
16321
10.REMOVE WATER INLET
|
Bolt |
|
Nut |
Remove the bolt, then separate the wiring harness clamp bracket.
Remove the bolt and nut, then remove the water inlet.
16331A
11.REMOVE THERMOSTAT
12261
12.REMOVE VENTILATION HOSE
Remove the ventilation hose.
12262
13.REMOVE NO. 2 VENTILATION HOSE
Remove the No. 2 ventilation hose.
22268
14.REMOVE NO. 2 THROTTLE BODY BRACKET
Remove the 2 bolts, then remove the No. 2 throttle body bracket.
88431
15.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (for LHD)
Remove the 4 bolts, then remove the No. 1 compressor mounting bracket.
16.REMOVE ENGINE WIRE
Remove the engine wire.
11101E
17.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
89422A
18.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
Using SST, remove the engine coolant temperature sensor.
11301K
19.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt, then remove the crankshaft position sensor.
16604B
20.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16603A
21.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16173
22.REMOVE WATER PUMP PULLEY
Using SST, hold the water pump pulley.
Remove the 3 bolts, then remove the water pump pulley.
16100
23.REMOVE ENGINE WATER PUMP ASSEMBLY
|
Bolt |
|
Nut |
Remove the 3 bolts and 2 nuts, then remove the engine water pump assembly.
22210
24.REMOVE THROTTLE BODY ASSEMBLY
Remove the 3 bolts and throttle body assembly.
22267
25.REMOVE THROTTLE BODY BRACKET
Remove the 2 bolts and throttle body bracket.
23807
26.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
23250
27.REMOVE FUEL INJECTOR ASSEMBLY
23291
28.REMOVE INJECTOR VIBRATION INSULATOR
17111
29.REMOVE INTAKE MANIFOLD
16035
30.REMOVE WATER HOSE JOINT
Disconnect No. 3 water by-pass hose from the water hose joint.
Remove the bolt and water hose joint.
21591
31.REMOVE WATER BY-PASS PLATE
Using a 6 mm socket hexagon wrench, remove the 2 bolts and water by-pass plate.
89615
32.REMOVE KNOCK CONTROL SENSOR
Remove the nut and knock control sensor.
12311
33.REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH
Remove the 4 bolts and No. 1 front engine mounting bracket RH.
12312
34.REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET
Remove the 4 bolts and No. 2 front engine mounting bracket.
16507
35.REMOVE RADIATOR PIPE SUB-ASSEMBLY
Remove the 2 bolts and the radiator pipe sub-assembly.
19500
36.REMOVE IGNITION COIL ASSEMBLY