1. DISCHARGE FUEL SYSTEM PRESSURE
2.DRAIN FUEL
Remove the drain plug, and drain the fuel into a container.
Clean the drain plug and install it with a new gasket.
37100
3.REMOVE PROPELLER SHAFT ASSEMBLY
77259C
4.DISCONNECT FUEL HOSE
| *1 | Fuel Tank To Canister Tube |
| *2 | Fuel Hose |
Loosen the hose clamp to disconnect the fuel hose from the fuel tank to canister tube.
77203A
5.DISCONNECT FUEL SUCTION TUBE SUB-ASSEMBLY
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Nylon Tube |
| *4 | O-ring |
| *5 | Fuel Main Tube |
|
Pinch |
|
Pull out |
Disengage the 2 claws and push down the retainer as illustrated.
Pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel main tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel main tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.
If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube and push and pull the fuel tube connector to release them.
77213B
6.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp bolt to disconnect the fuel tank to filler pipe hose from the fuel tank inlet pipe sub-assembly.
77269A
7.DISCONNECT FUEL TANK BREATHER HOSE
Loosen the hose clamp to disconnect the fuel tank breather hose from the fuel tank inlet pipe sub-assembly.
77100
8.REMOVE FUEL TANK ASSEMBLY
Disconnect the fuel pump connector.
Hold the fuel tank assembly using a transmission jack.
Remove the 4 bolts.
Operate the transmission jack, then remove the fuel tank assembly from the vehicle.
87268T
9.REMOVE NO. 1 PROTECTOR
Remove the 2 nuts and No. 1 protector.
77203A
10.REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY
Detach the fuel suction tube sub-assembly from the No. 1 fuel tube clamp.
| *1 | Retainer |
| *2 | O-ring |
| *3 | Nylon Tube |
| *4 | Fuel Tube Connector |
| *5 | Fuel Pump Tube |
|
Pinch |
|
Pull out |
Pinch the retainer to unlock it as illustrated, then pull the fuel suction tube sub-assembly (fuel tube connector) out of the fuel pump tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pump tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.
If the fuel tube connector and fuel pump tube are stuck, pinch the fuel pump tube and push and pull the fuel tube connector to release them.
Remove the retainer from the fuel pump tube.
Detach the fuel suction tube sub-assembly from the No. 2 fuel tube clamp.
| *1 | Retainer |
| *2 | O-ring |
| *3 | Fuel Tube Connector |
| *4 | Fuel Filter Tube |
| *5 | Nylon Tube |
|
Pinch |
|
Pull out |
Pinch the retainer to unlock it as illustrated, then pull the fuel suction tube sub-assembly (fuel tube connector) out of the fuel filter tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel filter tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.
If the fuel tube connector and fuel filter tube are stuck, pinch the fuel filter tube and push and pull the fuel tube connector to release them.
77204A
11.REMOVE FUEL TANK RETURN TUBE SUB-ASSEMBLY
Detach the fuel tank return tube sub-assembly from the No. 1 fuel tube clamp.
| *1 | Retainer |
| *2 | O-ring |
| *3 | Nylon Tube |
| *4 | Fuel Tube Connector |
| *5 | Fuel Pump Tube |
|
Pinch |
|
Pull out |
Pinch the retainer to unlock it as illustrated, then pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel pump tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pump tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.
If the fuel tube connector and fuel pump tube are stuck, pinch the fuel pump tube and push and pull the fuel tube connector to release them.
Remove the retainer from the fuel pump tube.
Detach the fuel tank return tube sub-assembly from the No. 2 fuel tube clamp.
| *1 | Retainer |
| *2 | O-ring |
| *3 | Fuel Tube Connector |
| *4 | Fuel Filter Tube |
| *5 | Nylon Tube |
|
Pinch |
|
Pull out |
Pinch the retainer to unlock it as illustrated, then pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel filter tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel filter tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.
If the fuel tube connector and fuel filter tube are stuck, pinch the fuel filter tube and push and pull the fuel tube connector to release them.
77285D
12.REMOVE NO. 1 FUEL TUBE CLAMP
Disengage the 2 claws to remove the No. 1 fuel tube clamp from the fuel tank assembly.
77286D
13.REMOVE NO. 2 FUEL TUBE CLAMP
Disengage the guide to remove the No. 2 fuel tube clamp from the fuel tank assembly as shown in the illustration.
23210P
14.REMOVE FUEL PUMP WITH MOTOR AND BRACKET ASSEMBLY
23300J
15.REMOVE FUEL FILTER ASSEMBLY
Remove the 2 bolts and fuel filter assembly.
77213B
16.REMOVE FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp bolt to remove the fuel tank to filler pipe hose from the fuel tank assembly.
77269A
17.REMOVE FUEL TANK BREATHER HOSE
Loosen the hose clamp to disconnect the fuel tank breather hose from the fuel tank assembly.
77108B
18.REMOVE FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY
Remove the fuel tank filler check valve sub-assembly from the fuel tank assembly.
77631A
19.REMOVE CENTER LOWER FUEL TANK PROTECTOR
Remove the 3 bolts and center lower fuel tank protector.
77100B
20.REMOVE FUEL HOSE CLAMP
Disengage the 4 claws to remove the fuel hose clamp from the fuel tank assembly.
77013
21.REMOVE NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Detach the No. 2 fuel tank breather tube sub-assembly from the fuel tank assembly.
Remove the 4 bolts and No. 2 fuel tank breather tube sub-assembly.
77380
22.REMOVE FUEL CUT OFF VALVE ASSEMBLY
Remove the fuel cut off valve assembly from the fuel tank assembly.
77141B
23.REMOVE NO. 1 FUEL TANK FLANGE REINFORCEMENT
Remove the 4 No. 1 fuel tank flange reinforcements from the fuel tank assembly.
77201
24.REMOVE FUEL TANK INLET PIPE SUB-ASSEMBLY
Remove the fuel tank cap assembly.
Remove the 2 bolts, then pull the fuel tank inlet pipe sub-assembly out of the fuel tank filler pipe shield.