Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › from 2015.08
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0015227 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 87107A 1.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (w/ Heater)

a.
E325096

Install the heater radiator unit sub-assembly.


b.
E325094

Install the screw.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for RHD)

a.

w/o Heater:

i.
E321247

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new No. 1 cooler evaporator sub-assembly is installed, add compressor oil to the No. 1 cooler evaporator sub-assembly as follows.


Capacity:

Add 25 cc (0.85 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



ii.

Engage each claw and install the upper case with the 7 screws.

E321245


iii.

Install the 7 screws.

E321244


iv.
E231842

Engage the No. 1 cooler thermistor connector clamp.



b.

w/ Heater:

i.
E238934

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new No. 1 cooler evaporator sub-assembly is installed, add compressor oil to the No. 1 cooler evaporator sub-assembly as follows.


Capacity:

Add 25 cc (0.85 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



ii.
E237826

Install the upper case.


iii.
E238931

Install the blower case.


iv.

Install the 24 screws.

E237591


v.
E231842

Engage the No. 1 cooler thermistor connector clamp.



Hide 88501 4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for LHD)

a.
E325097

Install the No. 1 cooler evaporator sub-assembly.

HINT:

If a new No. 1 cooler evaporator sub-assembly is installed, add compressor oil to the No. 1 cooler evaporator sub-assembly as follows.


Capacity:

Add 25 cc (0.85 fl. oz.)


Compressor oil:

ND-OIL8 or equivalent.



b.
E325092

Install the upper case.


c.
E325091

Install the blower case.


d.

Install the 28 screws.

E325090


e.
E325089

Engage the No. 1 cooler thermistor connector clamp.


Hide 5.INSTALL AIR FILTER CASE (for LHD)

a.
E325088

Engage the 4 claws to install the air filter case.


b.
E325087

Install the 2 screws.


Hide 6.INSTALL AIR FILTER CASE (for RHD)

a.
E321241

Engage the 5 claws to install the air filter case.


b.
E321240

Install the 2 screws.


Hide 88578B 7.INSTALL COOLER UNIT CASE PACKING

a.
E231838

Install a new cooler unit packing.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 88515 8.INSTALL COOLER EXPANSION VALVE

a.
E231841

Apply sufficient compressor oil to new 2 O-rings and the fitting surfaces of the cooler expansion valve.

Compressor oil:

ND-OIL8 or equivalent



b.

Install the 2 O-rings onto the No. 1 cooler evaporator sub-assembly.


c.

Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

HINT:

Use the same procedure for the RHD and LHD vehicles.



Hide 88550B 10.INSTALL BLOWER MOTOR ASSEMBLY