Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0560  Abnormal Backup System Power Supply  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 Abnormal Backup System Power Supply An open or short in the ECM back up power source circuit (1 trip detection logic).
·

Open or short in back up power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360379E02
1.021,2.198 2.094,2.396 1.073,0.198 10 false Battery 1.604,1.167 2.677,1.365 1.073,0.198 10 false FL MAIN 3.865,1.188 4.323,1.385 0.458,0.198 10 false EFI 5.104,1 5.563,1.198 0.458,0.198 10 false A24 5.146,0.813 5.458,1.01 0.313,0.198 10 false 13 5.104,2.229 5.563,2.427 0.458,0.198 10 false C50 5.115,2.042 5.573,2.24 0.458,0.198 10 false 105 5.76,3.104 6.219,3.302 0.458,0.198 10 false ECM 5.448,1.01 5.906,1.208 0.458,0.198 10 false BAT 5.438,2.229 5.75,2.427 0.313,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Inspect the battery.

Click herePower Source / Network>1NR-VE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

CHARGE OR REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
A348485C09
0.135,1.031 0.479,1.313 0.344,0.281 2.563,0.948 2.271,0.208 false 2.552,0.938 2.26,0.198 true 0.031,0.021 0.344,0.219 0.313,0.198 10 false *a 1.958,0.115 2.302,0.313 0.344,0.198 10 false BAT 0.177,1.083 0.635,1.281 0.458,0.198 10 false A24
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-13 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTC P0560 is output A
DTCs are not output B



A

B