Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.09
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM J

1NR-VE ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil assembly. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A357522E02
0.646,6.573 1.323,6.917 0.677,0.344 10 false Battery 0.5,5.792 1.177,6.031 0.677,0.24 10 false FL MAIN 0.719,0.51 1.188,0.813 0.469,0.302 10 false AM1 2.656,2.375 3.073,2.604 0.417,0.229 10 false IG2 2.094,2.813 3.802,3.219 1.708,0.406 10 false No. 1 Integration Relay 2.865,3.813 4.75,4.229 1.885,0.417 10 false No. 1 Ignition Coil Assembly 2.875,4.927 4.76,5.344 1.885,0.417 10 false No. 2 Ignition Coil Assembly 2.885,6 4.771,6.417 1.885,0.417 10 false No. 3 Ignition Coil Assembly 2.896,7.115 4.781,7.531 1.885,0.417 10 false No. 4 Ignition Coil Assembly 2.865,3.646 3.271,3.885 0.406,0.24 10 false C28 2.875,4.76 3.281,5.01 0.406,0.25 10 false C29 2.885,5.833 3.292,6.073 0.406,0.24 10 false C30 2.896,6.948 3.302,7.188 0.406,0.24 10 false C31 5.969,7.792 6.375,8.031 0.406,0.24 10 false C50 3.875,1.406 4.125,1.646 0.25,0.24 10 false 5 2.063,0.24 2.313,0.479 0.25,0.24 10 false 1 1.542,1.615 1.948,1.854 0.406,0.24 10 false 1E 1.583,1.406 1.833,1.646 0.25,0.24 10 false 5 4.448,1.75 4.917,2.052 0.469,0.302 10 false E/G 0.604,1.76 1.25,2.083 0.646,0.323 10 false IG MAIN 1.531,2.094 1.938,2.333 0.406,0.24 10 false 1D 1.573,1.885 1.823,2.125 0.25,0.24 10 false 1 3.833,1.615 4.24,1.854 0.406,0.24 10 false 1D 3.833,2.104 4.24,2.344 0.406,0.24 10 false 1F 3.823,1.896 4.073,2.135 0.25,0.24 10 false 18 1.719,0.771 4.052,1.146 2.333,0.375 10 false Ignition or Starter Switch Assembly 1.719,0.604 2.125,0.844 0.406,0.24 10 false E28 3.333,0.229 3.583,0.469 0.25,0.24 10 false 2 2.24,0.25 2.708,0.552 0.469,0.302 10 false AM 3.021,0.25 3.49,0.552 0.469,0.302 10 false IG1 5.427,3.458 5.677,3.698 0.25,0.24 10 false 40 5.427,4.573 5.677,4.813 0.25,0.24 10 false 41 5.427,5.635 5.677,5.875 0.25,0.24 10 false 42 5.427,6.74 5.677,6.979 0.25,0.24 10 false 43 6.313,7.792 6.802,8.094 0.49,0.302 10 false ECM 3.885,3.365 4.135,3.604 0.25,0.24 10 false + 3.5,3.448 3.75,3.688 0.25,0.24 10 false - 3.781,3.552 4.24,3.813 0.458,0.26 10 false IGT 3.885,4.479 4.135,4.719 0.25,0.24 10 false + 3.896,5.542 4.146,5.781 0.25,0.24 10 false + 3.896,6.635 4.146,6.875 0.25,0.24 10 false + 3.5,4.563 3.75,4.802 0.25,0.24 10 false - 3.5,5.635 3.75,5.875 0.25,0.24 10 false - 3.5,6.729 3.75,6.969 0.25,0.24 10 false - 3.781,4.667 4.24,4.927 0.458,0.26 10 false IGT 3.792,5.74 4.25,6 0.458,0.26 10 false IGT 3.792,6.844 4.25,7.104 0.458,0.26 10 false IGT 4.083,3.24 4.333,3.479 0.25,0.24 10 false 1 4.094,3.458 4.344,3.698 0.25,0.24 10 false 3 3.292,3.333 3.542,3.573 0.25,0.24 10 false 4 4.083,4.365 4.333,4.604 0.25,0.24 10 false 1 4.083,5.417 4.333,5.656 0.25,0.24 10 false 1 4.073,6.542 4.323,6.781 0.25,0.24 10 false 1 4.094,4.583 4.344,4.823 0.25,0.24 10 false 3 4.094,5.646 4.344,5.885 0.25,0.24 10 false 3 4.083,6.76 4.333,7 0.25,0.24 10 false 3 3.302,4.458 3.552,4.698 0.25,0.24 10 false 4 3.302,5.531 3.552,5.771 0.25,0.24 10 false 4 3.302,6.625 3.552,6.865 0.25,0.24 10 false 4 5.677,3.448 6.083,3.688 0.406,0.24 10 false IG1 5.677,4.563 6.083,4.802 0.406,0.24 10 false IG2 5.656,5.635 6.063,5.875 0.406,0.24 10 false IG3 5.677,6.74 6.083,6.979 0.406,0.24 10 false IG4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A200905C09
0.417,0.333 0.833,0.583 0.417,0.25 0.417,0.75 0.833,1 0.417,0.25 0.417,1.167 0.833,1.417 0.417,0.25 0.417,1.583 0.833,1.833 0.417,0.25 2.094,1.188 2.333,1.75 2.333,1.75 2.5,1.75 true 1.417,1.167 1.5,1.75 1.5,1.75 1.667,1.75 true 0.094,0.083 0.51,0.396 0.417,0.313 10 false *a 1.74,1.667 2.073,1.917 0.333,0.25 10 false + 0.5,0.375 0.958,0.656 0.458,0.281 10 false C28 0.51,0.792 0.969,1.073 0.458,0.281 10 false C29 0.5,1.208 0.958,1.49 0.458,0.281 10 false C30 0.51,1.625 0.969,1.906 0.458,0.281 10 false C31 2.594,1.656 3.01,1.969 0.417,0.313 10 false -
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C28-1 (+) - C28-4 (-) Ignition switch ON 11 to 14 V
C29-1 (+) - C29-4 (-) Ignition switch ON 11 to 14 V
C30-1 (+) - C30-4 (-) Ignition switch ON 11 to 14 V
C31-1 (+) - C31-4 (-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY (IG2 RELAY))
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C28-4 (-) - Body ground Always Below 1 Ω
C29-4 (-) - Body ground Always Below 1 Ω
C30-4 (-) - Body ground Always Below 1 Ω
C31-4 (-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C28-3 (IGT) - C50-40 (IG1) Always Below 1 Ω
C29-3 (IGT) - C50-41 (IG2) Always Below 1 Ω
C30-3 (IGT) - C50-42 (IG3) Always Below 1 Ω
C31-3 (IGT) - C50-43 (IG4) Always Below 1 Ω
C28-3 (IGT) or C50-40 (IG1) - Body ground Always 10 kΩ or higher
C29-3 (IGT) or C50-41 (IG2) - Body ground Always 10 kΩ or higher
C30-3 (IGT) or C50-42 (IG3) - Body ground Always 10 kΩ or higher
C31-3 (IGT) or C50-43 (IG4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY (IG2 RELAY))
a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the No. 1 integration relay (IG2 relay) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C28-1 (+) - 1D-5 Always Below 1 Ω
C29-1 (+) - 1D-5 Always Below 1 Ω
C30-1 (+) - 1D-5 Always Below 1 Ω
C31-1 (+) - 1D-5 Always Below 1 Ω
C28-1 (+) or 1D-5 - Body ground Always 10 kΩ or higher
C29-1 (+) or 1D-5 - Body ground Always 10 kΩ or higher
C30-1 (+) or 1D-5 - Body ground Always 10 kΩ or higher
C31-1 (+) or 1D-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 1 integration relay (IG2 relay).

Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG