Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  P0115  Engine Coolant Temperature Sensor System Open  P0117  Engine Coolant Temperature Sensor System Open/Low  P0118  Engine Coolant Temperature Sensor System Open/High  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Sensor System Open An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Sensor System Open/Low A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Sensor System Open/High An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360382E04
0.51,2.698 0.969,2.896 0.458,0.198 10 false C54 0.51,2.865 3.125,3.281 2.615,0.417 10 false Engine Coolant Temperature Sensor 2.229,1.938 2.385,2.135 0.156,0.198 10 false 1 2.229,1.354 2.385,1.552 0.156,0.198 10 false 2 5.313,1.354 5.771,1.552 0.458,0.198 10 false THW 5.052,1.354 5.365,1.552 0.313,0.198 10 false 32 5.323,1.948 5.635,2.146 0.313,0.198 10 false E2 4.99,1.948 5.448,2.146 0.458,0.198 10 false 100 5.979,0.938 6.292,1.135 0.313,0.198 10 false 5V 5.99,1.219 6.146,1.417 0.156,0.198 10 false R 5.49,3 5.948,3.198 0.458,0.198 10 false C50 5.844,3 6.302,3.198 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).



PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


e.

Read the value displayed on the GTS.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).




Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Between 75 and 100°C (167 and 212°F) C



A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor connector.

A207455C89
6.135,1.375 6.49,1.594 0.354,0.219 1.26,1.875 1.438,2.042 0.177,0.167 10 false *1 2.813,1.875 2.99,2.042 0.177,0.167 10 false *2 2.406,1.542 3.333,1.854 0.927,0.313 10 false E2 2.26,1.021 2.854,1.198 0.594,0.177 10 false THW 5.365,0.26 5.542,0.427 0.177,0.167 10 false *a 6.198,1.406 6.792,1.698 0.594,0.292 10 false C54
*1 Engine Coolant Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
- -



b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F) or more



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-2 - C50-32 (THW) Always Below 1 Ω
C54-1 - C50-100 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A280726C04
0.729,0.281 1.063,0.521 0.333,0.24 10 false *1 2.604,0.281 3.021,0.615 0.417,0.333 10 false *2 2.51,1.031 2.865,1.25 0.354,0.219 10 false THW 2.604,1.531 3.104,1.844 0.5,0.313 10 false E2
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F) or less.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-2 or C50-32 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR