Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  P0530  A/C Refrigerant Pressure Sensor System Malfunction  


DESCRIPTION

The air conditioner pressure sensor is attached to the high-pressure pipe block to detect an abnormal refrigerant pressure. A DTC is stored if abnormal refrigerant pressure is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0530 A/C Refrigerant Pressure Sensor System Malfunction Both of the following conditions are met (1 trip detection logic):
·

Refrigerant pressure is less than 0 MPa (0 kgf/cm2) or 3.187 MPa (32 kgf/cm2) or higher.

·

A/C volume switch is active.


·

Open or short in air conditioner pressure sensor circuit

·

Air conditioner pressure sensor

·

ECM


- DTC stored

WIRING DIAGRAM

A325176E04
0.49,2.865 2.646,3.281 2.156,0.417 10 false Air Conditioner Pressure Sensor 0.49,2.688 0.854,2.896 0.365,0.208 10 false A28 5.698,1.156 6.063,1.365 0.365,0.208 10 false VCO 5.698,1.74 6.177,1.948 0.479,0.208 10 false ACAD 6.052,2.99 6.417,3.198 0.365,0.208 10 false A24 6.052,3.167 6.635,3.406 0.583,0.24 10 false ECM 5.698,2.323 6.177,2.531 0.479,0.208 10 false E24 5.417,1.042 5.896,1.25 0.479,0.208 10 false 29 5.406,1.625 5.885,1.833 0.479,0.208 10 false 43 5.406,2.208 5.885,2.417 0.479,0.208 10 false 57 2.177,1.031 2.656,1.24 0.479,0.208 10 false 3 2.177,1.625 2.656,1.833 0.479,0.208 10 false 2 2.167,2.198 2.646,2.406 0.479,0.208 10 false 1 1.844,1.146 2.323,1.354 0.479,0.208 10 false VC 1.667,1.729 2.146,1.938 0.479,0.208 10 false VOUT 1.938,2.323 2.417,2.531 0.479,0.208 10 false E

PROCEDURE

1.INSPECT AIR CONDITIONER PRESSURE SENSOR (POWER SOURCE CIRCUIT)
a.
E202734C41
1.469,0.375 1.885,0.625 0.417,0.25 1.448,1.573 1.083,1.865 true 1.917,1.583 2.323,1.896 true 0.083,0.083 0.458,0.438 0.375,0.354 10 false *a 2.313,1.927 2.625,2.125 0.313,0.198 10 false VC 1.01,1.885 1.323,2.083 0.313,0.198 10 false E 1.563,0.417 2.021,0.656 0.458,0.24 10 false A28
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)


Disconnect the air conditioner pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A28-3 (VC) - A28-1 (E) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER PRESSURE SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER PRESSURE SENSOR)
2.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the air conditioner pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-43 (ACAD) - A28-2 (VOUT) Always Below 1 Ω
A24-43 (ACAD) or A28-2 (VOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR CONDITIONER PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AIR CONDITIONER PRESSURE SENSOR
a.

Replace the air conditioner pressure sensor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (P0530)
4.CHECK WHETHER DTC OUTPUT RECURS (P0530)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC P0530 is output B



A

END

B

5.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the air conditioner pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-29 (VCO) - A28-3 (VC) Always Below 1 Ω
A24-57 (E24) - A28-1 (E) Always Below 1 Ω
A24-29 (VCO) or A28-3 (VC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR