This Electronic Throttle Control System (ETCS) does not use a throttle cable.
These DTCs relate to the accelerator pedal position sensor.
The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2120 | Accelerator Pedal Position Sensor (Main) Open | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open or short in accelerator pedal sensor assembly circuit ·
ECM |
Comes on | DTC stored |
| P2122 | Accelerator Pedal Position Sensor (Main) Open/Low | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCPA circuit ·
Open or ground short in VPA circuit ·
ECM |
Comes on | DTC stored |
| P2123 | Accelerator Pedal Position Sensor (Main) Open/High | VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in EPA circuit ·
Short in VPA circuit ·
ECM |
Comes on | DTC stored |
| P2125 | Accelerator Pedal Position Sensor (Sub) Open | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open or short in accelerator pedal sensor assembly circuit ·
ECM |
Comes on | DTC stored |
| P2127 | Accelerator Pedal Position Sensor (Sub) Open/Low | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCP2 circuit ·
Open or ground short in VPA2 circuit ·
ECM |
Comes on | DTC stored |
| P2128 | Accelerator Pedal Position Sensor (Sub) Open/High | Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
·
Accelerator pedal sensor assembly ·
Open in EPA2 circuit ·
Short in VPA2 circuit ·
ECM |
Comes on | DTC stored |
| P2138 | Accelerator Pedal Position Sensor Main/Sub Voltage Correlation | Either of the following conditions is met for 2 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less. (b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less. |
·
Short between VPA and VPA2 circuits ·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS. Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.
| Trouble Area | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed | ||
|---|---|---|---|---|
| Main accelerator sensor voltage | Sub accelerator sensor voltage | Main accelerator sensor voltage | Sub accelerator sensor voltage | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.75 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.75 V |
Accelerator pedal positions are expressed as voltages.
| All of the following conditions are met | - |
| VPA voltage | Higher than 0.4 V, and less than 4.8 V |
| VPA2 voltage | Higher than 1.2 V, and less than 4.8 V |
| Difference between VPA and VPA2 voltages | Higher than 0.02 V |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Fully depress and release the accelerator pedal [B].
Check that 5 seconds or more have elapsed since the ignition switch to ON.
Enter the following menus: Powertrain / EFI / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Fully Depressed |
| *b | Fully Released |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.
Read the value displayed on the GTS.
| Accelerator Pedal Operation | Main accelerator sensor voltage | Sub accelerator sensor voltage | Difference between Main accelerator sensor voltage and Sub accelerator sensor voltage |
|---|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V | Higher than 0.02 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-6 (VPA1) - A24-44 (VPA) | Always | Below 1 Ω |
| A23-5 (EP1) - A24-58 (EPA) | Always | Below 1 Ω |
| A23-4 (VCP1) - A24-30 (VCP1) | Always | Below 1 Ω |
| A23-3 (VPA2) - A24-45 (VPA2) | Always | Below 1 Ω |
| A23-2 (EP2) - A24-59 (EPA2) | Always | Below 1 Ω |
| A23-1 (VCP2) - A24-31 (VCP2) | Always | Below 1 Ω |
| A23-6 (VPA1) or A24-44 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A23-4 (VCP1) or A24-30 (VCP1) - Body ground and other terminals | Always | 10 kΩ or higher |
| A23-3 (VPA2) or A24-45 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| A23-1 (VCP2) or A24-31 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
for LHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E88-6 (VPA1) - A24-44 (VPA) | Always | Below 1 Ω |
| E88-5 (EP1) - A24-58 (EPA) | Always | Below 1 Ω |
| E88-4 (VCP1) - A24-30 (VCP1) | Always | Below 1 Ω |
| E88-3 (VPA2) - A24-45 (VPA2) | Always | Below 1 Ω |
| E88-2 (EP2) - A24-59 (EPA2) | Always | Below 1 Ω |
| E88-1 (VCP2) - A24-31 (VCP2) | Always | Below 1 Ω |
| E88-6 (VPA1) or A24-44 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| E88-4 (VCP1) or A24-30 (VCP1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E88-3 (VPA2) or A24-45 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| E88-1 (VCP2) or A24-31 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
for RHD
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A23-4 (VCP1) - A23-5 (EP1) | Ignition switch ON | 4.5 to 5.5 V |
| A23-1 (VCP2) - A23-2 (EP2) | Ignition switch ON | 4.5 to 5.5 V |
for LHD
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E88-4 (VCP1) - E88-5 (EP1) | Ignition switch ON | 4.5 to 5.5 V |
| E88-1 (VCP2) - E88-2 (EP2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTCs are not output | B |
A
B