Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196182 REAR CRANKSHAFT OIL SEAL A

1NR-VE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustable attachments and plate lift attachments, place the engine assembly horizontally.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A360089C01
0.875,2.646 1.708,3.115 1.708,3.115 2.552,2.677 true 1.667,3.167 1.979,3.365 0.313,0.198 10 false *a
*a Seal Packing


Wipe off the excess seal packing, leaving only the specified amount in the areas shown in the illustration.


c.
A360088C01
0.896,2.604 1.667,3.135 1.667,3.135 2.531,2.646 true 1.656,3.156 1.969,3.313 0.313,0.156 10 false *a
*a Seal Packing (3.0 mm (0.118 in.))


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install a new rear engine oil seal within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.

·

When installing the rear oil seal after more than 10 minutes of seal packing application, make sure to remove the excess seal packing around the oil seal hole, and then reapply seal packing.




d.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free of foreign matter.



e.
A360090N01
1.583,1.792 2.031,0.99 true 0.875,0.802 1.052,0.542 true 1.281,1.781 1.74,1.979 0.458,0.198 10 false SST 1.063,0.375 1.521,0.573 0.458,0.198 10 false SST 1.219,1.333 1.677,1.531 0.458,0.198 10 false + 1.219,0.833 1.677,1.031 0.458,0.198 10 false -

Using SST and a hammer, tap in a rear engine oil seal until its surface is flush with the cylinder block sub-assembly and oil pan sub-assembly.

SST
09223-15030  09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure there is no foreign matter on the lip of the rear engine oil seal.

·

Make sure there is no oil or grease on the outer circumference of the rear engine oil seal.

·

Do not tap in the rear engine oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A361372N01
2.396,1.979 2.875,1.865 false 2.896,1.771 3.354,1.969 0.458,0.198 10 false SST

Using SST, hold the crankshaft.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Never turn the crankshaft pulley counterclockwise (when viewed from the front of the engine).



b.

Clean the 8 bolts and bolt holes.


c.
A057108C66
2.313,0.292 2.021,1.115 false 2.354,0.208 2.552,0.385 0.198,0.177 10 *a
*a Adhesive 1324


Apply adhesive to 2 or 3 threads of each bolt end.

Adhesive:

Toyota Genuine Adhesive 1324, Three bond 1324 or equivalent


NOTICE:

Install the bolt within 3 minutes of applying adhesive.



d.
A360086N01
1.729,0.5 1.885,0.698 0.156,0.198 10 true 1 1.896,1.719 2.052,1.917 0.156,0.198 10 true 2 1.198,1.125 1.354,1.323 0.156,0.198 10 true 3 2.333,1.146 2.49,1.344 0.156,0.198 10 true 4 1.385,0.635 1.542,0.833 0.156,0.198 10 true 5 2.219,1.531 2.375,1.729 0.156,0.198 10 true 6 1.313,1.563 1.469,1.76 0.156,0.198 10 true 7 2.156,0.635 2.313,0.833 0.156,0.198 10 true 8

Install the drive plate and ring gear sub-assembly and centering plate, and then uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 3.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 13405 4.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A361372N01
2.396,1.979 2.875,1.865 false 2.896,1.771 3.354,1.969 0.458,0.198 10 false SST

Using SST, hold the crankshaft.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Never turn the crankshaft pulley counterclockwise (when viewed from the front of the engine).



b.

Clean the 8 bolts and bolt holes.


c.
A057108C37
2.313,0.292 2.021,1.115 false 2.354,0.208 2.552,0.385 0.198,0.177 10 *a
*a Adhesive 1324


Apply adhesive to 2 or 3 threads of each bolt end.

Adhesive:

Toyota Genuine Adhesive 1324, Three bond 1324 or equivalent


NOTICE:

Install the bolt within 3 minutes of applying adhesive.



d.
A360085N01
1.74,0.552 1.896,0.75 0.156,0.198 10 true 1 1.875,1.698 2.031,1.896 0.156,0.198 10 true 2 1.271,1.135 1.427,1.333 0.156,0.198 10 true 3 2.313,1.146 2.469,1.344 0.156,0.198 10 true 4 1.406,0.667 1.563,0.865 0.156,0.198 10 true 5 2.146,1.573 2.302,1.771 0.156,0.198 10 true 6 1.385,1.542 1.542,1.74 0.156,0.198 10 true 7 2.146,0.719 2.302,0.917 0.156,0.198 10 true 8

Using several steps, uniformly install and uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 31250 5.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)