Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0197968 AUTOMATIC TRANSMISSION ASSEMBLY A

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12371 1.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Install the rear No. 1 engine mounting insulator with new 2 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


b.

Temporarily install the rear No. 1 engine mounting insulator with rear engine mounting bracket to the rear engine support member sub-assembly with a new bolt.

NOTICE:

Securely tighten the bolt after installing the engine assembly with automatic transmission assembly onto the vehicle.

for 1NR-VE: Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION

for 2NR-VE: Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION



Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C331417

Engage the splines of the input shaft and turbine runner.


b.
C331418

Insert the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm and engage the splines while rotating the torque converter.



c.
C331419

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter set bolt holes.


e.
C331420C01
1.469,0.396 1.781,0.219 true 2.375,0.875 2.531,0.729 true 2.688,0.771 2.542,1.031 true 1.302,1.615 1.698,1.854 true 1.813,0.094 2.125,0.292 0.313,0.198 10 false *1 1.781,1.823 2.094,2.021 0.313,0.198 10 false *2 2.188,0.823 2.5,1.021 0.313,0.198 10 false *1 2.406,1.063 2.719,1.26 0.313,0.198 10 false *2
*1 Engine Surface
*2 Drive Plate Surface


Using a vernier caliper and a straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter contact surface of the drive plate.


f.
C331421C01
2.635,1.625 2.792,1.823 0.156,0.198 10 false B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the step above.

Standard:

A + 16.5 mm (0.650 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.

·

Do not include the thickness of the set block.




g.

Apply MP grease to the torque converter tip.


Hide 12321E 3.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Temporarily connect the rear engine mounting bracket to the automatic transmission assembly with the 4 bolts.


b.
C331415N01
2.458,0.563 2.615,0.76 0.156,0.198 10 true A 0.958,0.292 1.125,0.469 0.167,0.177 10 true B 1.375,0.667 1.542,0.844 0.167,0.177 10 true C 1.76,0.698 1.927,0.875 0.167,0.177 10 true D

Temporarily tighten the bolt A.


c.

Securely tighten the 4 bolts in the following order; B, A, C and D.

Torque:
58.8 N*m (600 kgf*cm, 43 ft.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C249326C01
1.604,1.083 2.552,0.771 true 2.594,0.688 3.094,1.125 0.5,0.438 10 *1 0.906,1 1.396,1.448 0.49,0.448 10 *2
*1 Torque Converter Centerpiece
*2 Crankshaft


Apply clutch spline grease to the round of the crankshaft contact surface with the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

Approximately 1 g (0.0353 oz)



b.
C331422C01
0.604,0.344 1.229,0.615 true 2.583,1.24 2.958,1.385 true 3.031,1.344 3.292,1.552 0.26,0.208 10 false *1 0.427,0.24 0.688,0.448 0.26,0.208 10 false *1 2.094,2.396 2.406,2.594 0.313,0.198 10 false A 0.896,2.427 1.208,2.625 0.313,0.198 10 false A 0.51,3.344 0.823,3.542 0.313,0.198 10 false A 0.542,3.688 0.854,3.885 0.313,0.198 10 false B 0.76,4.146 1.073,4.344 0.313,0.198 10 false C 1.073,4.417 1.385,4.615 0.313,0.198 10 false C 1.521,4.469 1.833,4.667 0.313,0.198 10 false C 2.188,4.406 2.5,4.604 0.313,0.198 10 false C 2.708,3.583 3.021,3.781 0.313,0.198 10 false C
*1 Knock Pin


Temporarily install the automatic transmission assembly with the 9 bolts.

Bolt length:

57 mm (2.24 in.) for bolt A and bolt B

40 mm (1.57 in.) for bolt C


NOTICE:
·

Confirm that there are 2 knock pins on the transmission fitting surface of the engine assembly.

·

After installing the transmission, confirm that the torque converter rotates smoothly.




c.

Tighten the 3 bolts A to the specified torque.

Torque:
58.8 N*m (600 kgf*cm, 43 ft.*lbf)


d.

Tighten the bolt B and other 5 bolts C to the specified torque.

Torque:
Bolt B : 58.8 N*m (600 kgf*cm, 43 ft.*lbf)
Bolt C : 36.8 N*m (375 kgf*cm, 27 ft.*lbf)


e.

Turn the crankshaft to gain access and install the 6 bolts while holding the crankshaft pulley bolt with a wrench.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

First install the silver blue bolt and then the remaining 5 black bolts.



Hide 28100 5.INSTALL STARTER ASSEMBLY (for 1NR-VE)

Hide 28100 6.INSTALL STARTER ASSEMBLY (for 2NR-VE)

Hide 32906 7.INSTALL OIL COOLER TUBE SUB-ASSEMBLY

a.

Temporarily install the oil cooler tube sub-assembly with the 2 union bolts and 2 new gaskets.

HINT:

Tighten the union bolt A, and then union bolt B.



b.

Tighten the 3 bolts in the following order; C, D and E.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

C331411N01
3.563,1.365 3.76,1.563 0.198,0.198 10 true A 0.75,0.51 0.938,0.698 0.188,0.188 10 false B 4.229,0.552 4.417,0.729 0.188,0.177 10 true C 4.958,1.479 5.146,1.656 0.188,0.177 10 true D 6.531,1.208 6.719,1.385 0.188,0.177 10 true E


c.

Tighten the 2 union bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 35013 8.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto the transmission oil filler tube sub-assembly.


b.

Install the transmission oil filler tube sub-assembly with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 35103 9.INSTALL TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

a.

Install the transmission oil level dipstick sub-assembly.


Hide 10.INSTALL ENGINE WIRE

a.

Connect the clamps and connectors to the automatic transmission assembly.


Hide 12.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for 1NR-VE)

Hide 13.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for 2NR-VE)