15708
1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.
13101
2.INSTALL PISTON WITH PIN SUB-ASSEMBLY
If the piston pin has been removed from the piston, replace the piston, piston pin and connecting rod with new ones.
Gradually heat a new connecting rod to 80 °C (176 °F) or more.
| *a | Front Mark |
Coat a new piston pin and pin holes of a new piston with engine oil.
Align the front mark of the piston with that of the connecting rod.
Using SST, press in the piston pin.
| *1 | Piston Pin | *2 | Connecting Rod |
| *3 | Piston | - | - |
| *a | Front Mark | *b | Contact |
| *c | 1.35 to 2.65 mm (0.053 to 0.104 in.) | - | - |
|
Rear Side | - | - |
Press in the piston pin from the side of the piston with the front mark as shown in the illustration.
With the connecting rod fully inserted into the piston end, press in the piston pin until it is flush with the piston surface.
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
13011
3.INSTALL PISTON RING SET
| *1 | Side Rail (Upper) |
| *2 | Expander Spacer |
| *3 | Side Rail (Lower) |
| *a | Expander Spacer and Side Rail Groove |
Install the expander spacer and 2 side rails by hand, as shown in the illustration.
| *1 | No. 1 Compression Ring |
| *2 | No. 2 Compression Ring |
|
Upward |
Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.
Install the No. 2 compression ring with the code mark (T2) facing upward.
| *1 | Side Rail (Upper) |
| *2 | No. 1 Compression Ring and Expander Spacer |
| *3 | Side Rail (Lower) |
| *4 | No. 2 Compression Ring |
| *a | F Mark |
Position the piston rings so that the ring ends are as shown in the illustration.
The end gap of each piston ring must be positioned as shown in the illustration regardless of the position of the F mark on the piston.
11711
4.INSTALL CRANKSHAFT BEARING
Install the 5 upper crankshaft bearings to the cylinder block sub-assembly.
| *a | Correct | *b | Incorrect |
|
Engine Front | - | - |
Align the oil holes in the crankshaft bearing with the oil holes in the cylinder block sub-assembly.
Do not apply engine oil to the crankshaft bearings or the contact surfaces.
Install the lower crankshaft bearing.
Install the 5 lower crankshaft bearings onto the crankshaft bearing cap.
Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.
0.8 mm (0.0315 in.) or less
Do not apply engine oil to the crankshaft bearings or the contact surfaces.
11791
5.INSTALL UPPER CRANKSHAFT THRUST WASHER
| *a | Oil Grooves |
Install the 2 upper crankshaft thrust washers under the No. 3 journal of the cylinder block sub-assembly with the oil grooves facing outward.
Apply engine oil to the 2 upper crankshaft thrust washers.
13411
6.INSTALL CRANKSHAFT
Apply engine oil to the upper crankshaft bearings, crankshaft journal and install the crankshaft on the cylinder block sub-assembly.
Apply engine oil to the lower crankshaft bearings.
| *a | Number Mark |
|
Engine Front |
Confirm the number marks and install the crankshaft bearing caps and No. 3 crankshaft bearing cap on the cylinder block sub-assembly.
Apply a light coat of engine oil to the threads and under the crankshaft bearing cap set bolts.
Temporarily install the 10 crankshaft bearing cap set bolts.
Step 1
Uniformly tighten the 10 crankshaft bearing cap set bolts in the order shown in the illustration.
Step 2
| *a | Paint Mark |
| *b | 90° |
|
Engine Front |
Mark the front of the crankshaft bearing cap set bolts with paint.
Further tighten the crankshaft bearing cap set bolts an additional 90° in the order shown in the previous illustration.
Check that the paint mark is now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the crankshaft thrust clearance.
Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION
13041
7.INSTALL CONNECTING ROD BEARING
Install the connecting rod bearing to the connecting rod and connecting rod cap.
Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.
0.5 mm (0.0197 in.) or less
Do not apply engine oil to the connecting rod bearings or the contact surfaces.
Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.
0.5 mm (0.0197 in.) or less
Do not apply engine oil to the connecting rod bearings or the contact surfaces.
8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD
Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.
| *1 | Side Rail (Upper) |
| *2 | No. 1 Compression Ring and Expander Spacer |
| *3 | Side Rail (Lower) |
| *4 | No. 2 Compression Ring |
| *a | F Mark |
Position the piston rings so that the ring ends are as shown in the illustration.
The end gap of each piston ring must be positioned as shown in the illustration regardless of the position of the F mark on the piston.
| *a | Front Mark |
Using a piston ring compressor, push the correctly numbered piston sub-assembly with connecting rod sub-assembly into the cylinder block sub-assembly with the front mark of the piston facing forward.
When inserting the piston with pin sub-assembly with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.
Match the numbered connecting rod cap with the connecting rod.
| *a | Front Mark |
Check that the front mark of the connecting rod cap is facing in the correct direction.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
Install the connecting rod bolts.
Step 1
Using SST, install and alternately tighten the connecting rod bolts of the connecting rod cap in several steps.
Step 2
| *a | Paint Mark |
| *b | 90° |
|
Engine Front |
Mark the front of the connecting rod bolts with paint.
Further tighten the connecting rod bolts an additional 90° as shown in the illustration.
Check that the paint mark is now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the connecting rod thrust clearance.
Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION
13521A
9.INSTALL CRANKSHAFT TIMING GEAR KEY
Install the crankshaft timing gear key to the crankshaft.