Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › ENGINE UNIT › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196194 ENGINE UNIT G

2NR-VE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A125485

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free of dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.
A286731C04
1.094,0.75 1.573,0.479 true 1.948,0.49 2.417,0.698 true 1,1.198 1.615,0.917 true 1.885,0.938 2.521,1.094 true 1.021,1.448 1.615,1.313 true 1.885,1.313 2.469,1.417 true 0.896,1.844 1.625,1.781 true 1.885,1.781 2.573,1.875 true 0.802,2.313 1.635,2.5 true 1.917,2.5 2.698,2.281 true 0.781,2.771 0.781,2.49 true 2.698,2.76 2.698,2.479 true 1.333,3.333 1.521,2.844 true 1.677,1.229 1.99,1.385 0.313,0.156 10 *f 1.708,2.438 2.021,2.667 0.313,0.229 10 *g 1.688,1.708 2,1.865 0.313,0.156 10 *d 0.729,2.792 1.042,2.948 0.313,0.156 10 *e 0.688,0.229 1,0.385 0.313,0.156 10 *a 2.635,0.229 2.948,0.385 0.313,0.156 10 *b 1.688,0.833 2,0.99 0.313,0.156 10 *c 1.563,2.75 2.021,2.948 0.458,0.198 10 SST 1.625,0.396 2.083,0.594 0.458,0.198 10 SST 2.615,2.792 2.927,2.99 0.313,0.198 10 *e
*a Correct
*b Incorrect
*c Taper Part
*d Low Pressure Chamber
*e High Pressure Chamber
*f Plunger
*g Check Ball


Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed it.

OK:

Plunger moves up and down.


NOTICE:

When bleeding the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, the high-pressure chamber will not be bled.



e.

After bleeding, remove SST. Then, try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13050 3.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Install the camshaft timing gear assembly.

i.

Check that the straight pin is installed on the camshaft.


ii.
A198838C17
2.094,1.021 2.271,0.229 false 2.271,0.229 2.406,0.229 false 0.688,1.125 1.167,1.823 false 1.167,1.823 1.563,1.823 false 1.615,1.74 2.094,2.052 0.479,0.313 10 *a 2.448,0.146 2.865,0.448 0.417,0.302 10 *b
*a Key Groove
*b Straight Pin


Fit the camshaft timing gear assembly and camshaft together by aligning the key groove and straight pin.

NOTICE:
·

Do not forcefully push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.

·

Do not turn the camshaft timing gear assembly in the retard direction (clockwise).




iii.

Tighten the bolt with the camshaft timing gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)



b.

Check the locked state of the camshaft timing gear assembly.

i.

Confirm that the camshaft timing gear assembly is locked.



c.
A198832C09
1.958,1.271 2.396,1.271 false 1.438,1.438 0.99,1.438 false 2.198,2.885 1.677,2.417 1.677,2.417 1.375,2.76 true 1.365,3.365 0.781,3.365 true 2.083,3.031 2.583,3.229 2.583,3.229 2.115,3.177 true 0.792,3.042 1.323,2.823 true 1.792,3.719 2.479,3.979 true 2.458,1.167 3.125,1.49 0.667,0.323 10 false *d 0.802,1.333 1.094,1.594 0.292,0.26 10 false *c 1.583,2.198 1.885,2.385 0.302,0.188 10 false *e 0.583,3.25 1,3.427 0.417,0.177 10 false *a 2.656,3.188 3.063,3.385 0.406,0.198 10 false *b 2.531,3.917 2.927,4.198 0.396,0.281 10 false *f 0.594,2.948 1,3.146 0.406,0.198 10 false *b
*a Open
*b Close
*c Advance Side Path
*d Retard Side Path
*e Rubber
*f Vinyl Tape


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the groove of the camshaft. Plug 3 of the paths with pieces of rubber.



ii.

Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.


iii.
A198833C04
1.635,1.344 2.563,1.344 true 2.594,1.26 3.25,1.604 0.656,0.344 10 *a
*a Advance Side Path


While applying approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the oil paths, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep engine oil from spraying.


NOTICE:

Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.


HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leaks from the port, releasing the lock pin may be difficult.





d.

Check for smooth rotation.

i.

Turn the camshaft timing gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.

NOTICE:

Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.




Hide 13070A 4.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Install the camshaft timing exhaust gear assembly.

i.

Check that the straight pin is installed on the No. 2 camshaft.


ii.
A198839C15
2.177,0.979 2.344,0.188 false 2.344,0.188 2.479,0.188 false 0.792,1.063 1.281,1.781 false 1.281,1.781 1.667,1.781 false 1.75,1.708 2.156,2 0.406,0.292 10 *a 2.542,0.115 2.865,0.333 0.323,0.219 10 *b
*a Key Groove
*b Straight Pin


Fit the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the key groove and straight pin.

NOTICE:
·

Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.

·

Be sure not to turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).




iii.

Tighten the bolt with the camshaft timing exhaust gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)



b.

Check locked state of the camshaft timing exhaust gear assembly.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.



c.
A198834C16
1.969,1.271 2.375,1.271 false 1.448,1.448 0.99,1.448 false 2.01,3.073 1.656,2.375 1.656,2.375 1.396,2.771 true 1.354,3.375 0.771,3.375 true 0.74,3.083 1.333,2.813 true 1.844,3.573 2.563,3.979 true 2.094,3.031 2.542,3.031 true 2.104,3.167 2.552,3.448 true 0.75,1.385 1.417,1.708 0.667,0.323 10 false *d 2.406,1.188 3.052,1.521 0.646,0.333 10 false *c 1.563,2.167 2.104,2.354 0.542,0.188 10 false *e 0.563,3.271 0.979,3.448 0.417,0.177 10 false *a 2.635,3.406 3.042,3.604 0.406,0.198 10 false *b 2.625,3.885 3.365,4.063 0.74,0.177 10 false *f 0.542,3 0.948,3.198 0.406,0.198 10 false *b 2.573,2.948 2.99,3.125 0.417,0.177 10 false *a
*a Open
*b Close
*c Advance Side Path
*d Retard Side Path
*e Rubber
*f Vinyl Tape


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

The 4 oil paths are provided in the grooves. Plug 2 paths with rubber pieces.



ii.

Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.


iii.
A198837C06
1.583,1.365 0.99,0.594 0.99,0.594 0.667,0.594 true 1.875,1.26 2.604,0.583 2.604,0.583 2.833,0.583 true 2.875,0.5 3.208,1.031 0.333,0.531 10 *a 0.469,0.5 0.76,0.958 0.292,0.458 10 *b
*a Advance Side Path
*b Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 paths (the advance side path and the retard side path).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep engine oil from spraying.



iv.
A198835C05
1.573,1.792 0.813,0.875 true 1.875,1.677 2.583,0.958 true 2.635,0.865 3.271,1.198 0.635,0.333 10 *c 0.625,0.781 1.281,1.115 0.656,0.333 10 *d 0.698,2.594 1.625,2.75 0.927,0.156 10 *a 2.667,2.594 3.313,2.917 0.646,0.323 10 *b
*a Hold Pressure
*b Release Pressure
*c Advance Side Path
*d Retard Side Path


Make sure that the camshaft timing exhaust gear assembly turns in the retard direction (clockwise) when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



v.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




d.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.

NOTICE:

When the air pressure is released from the advance side path, then from the retard side path, the camshaft timing exhaust gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




e.

Check the locked state at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly is locked at the most advanced position.



Hide 13506 5.INSPECT CHAIN SUB-ASSEMBLY

a.
A162995C18
1.667,1.219 2.906,1.448 1.24,0.229 10 *a 0.823,1.719 0.938,1.885 0.115,0.167 10 1 0.99,1.719 1.125,1.896 0.135,0.177 10 2 1.146,1.719 1.271,1.885 0.125,0.167 10 3 1.313,1.719 1.448,1.906 0.135,0.188 10 4 1.458,1.719 1.583,1.896 0.125,0.177 10 5 0.677,1.719 0.802,1.917 0.125,0.198 10 0 2.469,1.719 2.688,1.896 0.219,0.177 10 14 2.708,1.719 2.948,1.885 0.24,0.167 10 15
*a Measurement Area


Pull the chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain sub-assembly elongation:

114.8 mm (4.519 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is greater than the maximum, replace the chain sub-assembly.


Hide 13050 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A198690C05
0.729,2.667 1.542,3.125 1.542,3.125 2.333,2.667 true 1.49,3.156 1.958,3.427 0.469,0.271 10 *a
*a Chain Roller


Place the chain sub-assembly around the camshaft timing gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.

Minimum camshaft timing gear assembly diameter (with chain sub-assembly):

96.8 mm (3.811 in.)


NOTICE:

The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.


Hide 13070A 7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A198692C05
0.708,2.667 1.531,3.146 1.531,3.146 2.333,2.656 true 1.479,3.177 2.042,3.375 0.563,0.198 10 *a
*a Chain Roller


Place the chain sub-assembly around the camshaft timing exhaust gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.

Minimum camshaft timing exhaust gear assembly diameter (with chain sub-assembly):

96.8 mm (3.811 in.)


NOTICE:

The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.


Hide 13521 8.INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A198693C05
0.76,2.667 1.625,3.167 1.625,3.167 2.49,2.656 true 1.583,3.198 2.073,3.417 0.49,0.219 10 *a
*a Chain Roller


Place the chain sub-assembly around the crankshaft timing gear or sprocket.


b.

Using a vernier caliper, measure the diameter of the crankshaft timing gear or sprocket and chain sub-assembly.

Minimum crankshaft timing gear or sprocket diameter (with chain sub-assembly):

51.1 mm (2.012 in.)


NOTICE:

The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing gear or sprocket.


Hide 13591 9.INSPECT TIMING CHAIN TENSION ARM

a.
A198696

Using a vernier caliper, measure the timing chain tension arm for wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is greater than the maximum, replace the timing chain tension arm.


Hide 13566B 10.INSPECT TIMING CHAIN GUIDE

a.
A363000

Using a vernier caliper, measure the timing chain guide for wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is greater than the maximum, replace the timing chain guide.


Hide 13562 11.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A198694

Using a vernier caliper, measure the No. 2 chain vibration damper for wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is greater than the maximum, replace the No. 2 chain vibration damper.


Hide 13540 12.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A199356C04
2.083,0.51 2.521,0.667 0.438,0.156 10 *a 1.573,1.583 1.969,1.74 0.396,0.156 10 *b 1.719,3.219 2.115,3.375 0.396,0.156 10 *c
*a Raise
*b Move
*c Lock


Check that the plunger moves smoothly when the ratchet pawl is raised by hand.


b.

Release the ratchet pawl, then check that the plunger is locked in place by the ratchet pawl and does not move when pushed by hand.


Hide 13511 13.INSPECT CAMSHAFT

a.
A198697

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.04 mm (0.00157 in.)


If the runout is greater than the maximum, replace the camshaft.



b.
A198698

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.749 to 41.849 mm (1.6437 to 1.6476 in.)


Minimum cam lobe height:

41.499 mm (1.6338 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.
A198699

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Position Specified Condition
No. 1 34.454 to 34.470 mm (1.3565 to 1.3571 in.)
Other 22.954 to 22.970 mm (0.9037 to 0.9043 in.)


If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CYLINDER HEAD>INSPECTION



Hide 13512 14.INSPECT NO. 2 CAMSHAFT

a.
A198697

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.04 mm (0.00157 in.)


If the runout is greater than the maximum, replace the No. 2 camshaft.



b.
A198698

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.0 to 41.1 mm (1.6142 to 1.6181 in.)


Minimum cam lobe height:

40.80mm (1.6063 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.
A198699

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Position Specified Condition
No. 1 34.454 to 34.470 mm (1.3565 to 1.3571 in.)
Other 22.954 to 22.970 mm (0.9037 to 0.9043 in.)


If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CYLINDER HEAD>INSPECTION



Hide 11101A 15.INSPECT CYLINDER HEAD SET BOLT

a.
A199982C06
1.594,0.458 2.24,0.854 0.646,0.396 10 *a
*a Measurement Length


Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard length:

125.3 to 126.7 mm (4.9331 to 4.9882 in.)


Maximum length:

128.2 mm (5.047 in.)


If the length is greater than the maximum, replace the cylinder head set bolt with a new one.


Hide 25051 16.INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A363001

Using a straightedge and feeler gauge, check the surface cylinder head sub-assembly for warpage.

Maximum warpage:

0.8 mm (0.0315 in.)


HINT:

If the warpage is greater than the maximum, replace the exhaust manifold converter sub-assembly.