Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › CYLINDER HEAD › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196195 CYLINDER HEAD G

2NR-VE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, check the surfaces which contact the cylinder head sub-assembly and manifolds for warpage.

A363007C01
0.365,1.198 0.677,1.354 0.313,0.156 10 false *a 2.729,1.76 3.042,1.917 0.313,0.156 10 false *b 4.99,1.75 5.302,1.906 0.313,0.156 10 false *c
*a Cylinder Block Side *b Intake Manifold Side
*c Exhaust Manifold side - -


Maximum Warpage:
Item Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


If the warpage is greater than the maximum, replace the cylinder head sub-assembly.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A363008

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

If cracked, replace the cylinder head sub-assembly.


Hide 3.INSPECT VALVE SEATS

a.
A146287C09
2.927,1.313 3.333,1.583 0.406,0.271 10 *a
*a Width


Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.

Check the valve face and valve seat according to the following procedure:

i.

If Prussian blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.


ii.

If Prussian blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contact is in the middle of the valve face with the valve seat width between 1.2 and 1.7 mm (Intake side (0.0472 and 0.0669 in.)).


iv.

Check that the valve seat contact is in the middle of the valve face with the valve seat width between 1.0 and 1.4 mm (Exhaust side (0.0394 and 0.0551 in.)).



Hide 4.INSPECT CAMSHAFT THRUST CLEARANCE


b.
A198669

Using a dial indicator, measure the camshaft thrust clearance while moving the camshaft back and forth.

Standard Thrust Clearance:
Item Specified Condition
Intake 0.06 to 0.20 mm (0.00236 to 0.00787 in.)
Exhaust 0.06 to 0.20 mm (0.00236 to 0.00787 in.)


Maximum Thrust Clearance:
Item Specified Condition
Intake 0.215 mm (0.00846 in.)
Exhaust 0.215 mm (0.00846 in.)


If the camshaft thrust clearance is greater than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.


Hide 5.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft bearing caps and camshaft journals.


b.

Place the camshafts on the camshaft housing sub-assembly.


c.
A198670C08
1.76,1.271 1.104,0.146 1.104,0.146 0.927,0.146 true 0.688,0.073 1.229,0.49 0.542,0.417 10 false *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A198671C08
0.885,0.188 1.01,0.188 1.01,0.188 1.76,1.313 true 0.635,0.094 0.865,0.375 0.229,0.281 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.030 to 0.067 mm (0.00118 to 0.00264 in.)


Maximum Oil Clearance:

0.08 mm (0.00315 in.)


NOTICE:

Completely remove the Plastigage after the inspection.


If the camshaft oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.


Hide 13711B 6.INSPECT INNER COMPRESSION SPRING

a.
A314490

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

57.13 mm (2.2492 in.)


If the free length is not as specified, replace the inner compression spring.


b.
A319225C26
1.448,0.396 1.76,0.552 0.313,0.156 10 false *a 0.938,1.313 1.25,1.552 0.313,0.24 10 false *b
*a Deviation
*b 50 mm (1.97 in.)


Using a steel square and feeler gauge, measure the deviation of the inner compression spring as shown in the illustration.

Maximum deviation:

1.75 mm (0.0689 in.)

Maximum angle:

2°


If the deviation is greater than the maximum, replace the inner compression spring.


Hide 13711 7.INSPECT INTAKE VALVE

a.
A126904

Using a gasket scraper, scrape off any carbon on the intake valve head.


b.

Using a wire brush, thoroughly clean the valve.


c.
A121380C12
1.885,1.031 2.823,1.177 0.938,0.146 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard overall length:

103.35 mm (4.0689 in.)


Minimum overall length:

102.85 mm (4.0492 in.)


If the overall length is less than the minimum, replace the intake valve.


d.
A121378

Using a micrometer, measure the diameter of the intake valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.21535 to 0.21594 in.)


If the valve stem diameter is not as specified, check the valve guide bush oil clearance.


e.
A146308C04
0.635,1.781 0.948,1.979 0.313,0.198 10 *a
*a Margin Thickness


Using a vernier caliper, measure the intake valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


Hide 13715 8.INSPECT EXHAUST VALVE

a.
A126904

Using a gasket scraper, scrape off any carbon on the exhaust valve head.


b.

Using a wire brush, thoroughly clean the valve.


c.
A121383C11
1.865,0.969 2.813,1.135 0.948,0.167 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard overall length:

104.5 mm (4.114 in.)


Minimum overall length:

104.0mm (4.0945 in.)


If the overall length is less than the minimum, replace the exhaust valve.


d.
A121381

Using a micrometer, measure the diameter of the exhaust valve stem.

Standard valve stem diameter:

5.465 to 5.480 mm (0.21516 to 0.21575 in.)


If the valve stem diameter is not as specified, check the valve guide bush oil clearance.


e.
A121382C15
0.438,1.833 1.333,2.031 0.896,0.198 10 *a
*a Margin Thickness


Using a vernier caliper, measure the exhaust valve head margin thickness.

Standard margin thickness:

1.15 mm (0.0453 in.)


Minimum margin thickness:

0.65 mm (0.0256 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


Hide 9.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A198672

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard bushing inside diameter:

5.51 to 5.53 mm (0.2169 to 0.2177 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.080 mm (0.00315in.)
Exhaust 0.085 mm (0.00335in.)


If the oil clearance is greater than the maximum, replace the valve and valve guide bush.