77201
1.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY
Install the fuel tank inlet pipe sub-assembly with the 2 bolts in the order shown in the illustration.
Install the fuel tank cap assembly.
77277R
2.INSTALL FUEL TANK FILLER PIPE PROTECTOR
Install the fuel tank filler pipe protector with 3 new clips.
77141B
3.INSTALL NO. 1 FUEL TANK FLANGE REINFORCEMENT
Install the 4 No. 1 fuel tank flange reinforcements to the fuel tank assembly.
77380
4.INSTALL FUEL CUT OFF VALVE ASSEMBLY
Install the fuel cut off valve assembly onto the fuel tank assembly as shown in the illustration.
77013
5.INSTALL NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
| *a | Groove |
| *b | Protrusion |
Align the protrusion of the fuel tank assembly with the groove of the No. 2 fuel tank breather tube sub-assembly, then install the No. 2 fuel tank breather tube sub-assembly with the 4 bolts.
Attach the No. 2 fuel tank breather tube sub-assembly to the fuel tank assembly.
77259G
6.INSTALL FUEL HOSE CLIP
Engage the 4 claws to install the fuel hose clip.
77108B
7.INSTALL FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY
Install the fuel tank filler check valve sub-assembly as shown in the illustration.
Insert the fuel tank filler check valve sub-assembly until its claw fits into the spool.
The valve should smoothly open and close with its own weight after installing the valve.
77269A
8.INSTALL FUEL TANK BREATHER HOSE
| *1 | Tank Flange |
| *a | Tank Side |
| *b | 0 to 3 mm (0 to 0.12 in.) |
| *c | 2 to 7 mm (0.08 to 0.28 in.) |
| *d | Upper Side |
| *e | LH Side |
Install the fuel tank breather hose onto the fuel tank assembly with the hose clamp as shown in the illustration.
77213B
9.INSTALL FUEL TANK TO FILLER PIPE HOSE
| *1 | Fuel Tank Assembly |
| *2 | Spacer |
| *3 | Tank Flange |
| *a | Tank Side |
| *b | Paint Mark |
| *c | 0 to 3 mm (0 to 0.12 in.) |
| *d | 2 to 10 mm (0.08 to 0.39 in.) |
| *e | Upper Side |
| *f | LH Side |
Check that the fuel tank filler check valve sub-assembly is securely installed to the fuel tank assembly.
Install the fuel tank to filler pipe hose onto the fuel tank assembly with the hose clamp as shown in the illustration.
Install the fuel tank to filler pipe hose so the paint mark faces upward at the fuel tank side.
Tighten the hose clamp until it comes into contact with the spacer.
77286D
10.INSTALL NO. 2 FUEL TUBE CLAMP
Engage the guide to install the No. 2 fuel tube clamp to the fuel tank assembly.
77285D
11.INSTALL NO. 1 FUEL TUBE CLAMP
Engage the 2 claws to install the No. 1 fuel tube clamp to the fuel tank assembly.
23300J
12.INSTALL FUEL FILTER ASSEMBLY
Install the fuel filter assembly with the 2 bolts.
13.CONNECT FUEL PUMP HARNESS
Connect the 2 fuel pump harness clamps.
77020A
14.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
87268T
15.INSTALL NO. 1 PROTECTOR
Install the No. 1 protector with the 2 nuts.
77631A
16.INSTALL CENTER LOWER FUEL TANK PROTECTOR
Install the center lower fuel tank protector with the 3 bolts.
77100
17.INSTALL FUEL TANK ASSEMBLY
Operate the transmission jack to install the fuel tank assembly onto the vehicle.
Tighten the 4 bolts in the sequence shown in the illustration.
Connect the fuel pump connector.
77269A
18.CONNECT FUEL TANK BREATHER HOSE
| *a | Inlet Pipe Side |
| *b | 0 to 3 mm (0 to 0.12 in.) |
| *c | 2 to 7 mm (0.08 to 0.28 in.) |
| *d | Upper Side |
| *e | LH Side |
Connect the fuel tank breather hose to the fuel tank inlet pipe sub-assembly as shown in the illustration.
77213B
19.CONNECT FUEL TANK TO FILLER PIPE HOSE
| *1 | Spacer |
| *a | Inlet Pipe Side |
| *b | 2 to 15 mm (0.08 to 0.59 in.) |
| *c | 0 to 3 mm (0 to 0.12 in.) |
| *d | Upper Side |
| *e | LH Side |
Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe sub-assembly as shown in the illustration.
Tighten the hose clamp until it comes into contact with the spacer.
77204A
20.CONNECT FUEL TANK RETURN TUBE
| *1 | Retainer |
| *2 | Fuel Main Tube |
|
Push |
Insert the fuel tank return tube until it comes into contact with the fuel main tube, then push in the retainer until it makes a click sound.
Check that there are no scratches or foreign matter around the connected parts of the fuel main tube and fuel tank return tube before this work.
After connecting the fuel tank return tube , check that the fuel main tube and fuel tank return tube are securely connected by pulling them.
If connecting the tubes is too tight, apply a light coat of appropriate lubricant or gasoline to the tip of the fuel main tube.
77259C
21.CONNECT FUEL HOSE
| *a | Upper Side |
| *b | RH Side |
Connect the fuel hose to the fuel tank to canister tube with the clip as shown in the illustration.
37110
22.INSTALL PROPELLER SHAFT ASSEMBLY
23.ADD FUEL
24.INSPECT FOR FUEL LEAK