Home › Engine / Hybrid System › 2NR-VE FUEL › FUEL INJECTOR › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042276 2NR-VE FUEL _0196204 FUEL INJECTOR G

2NR-VE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A154756C10
2.938,0.469 2.948,0.198 2.948,0.198 2.615,0.198 false 2.427,0.125 2.615,0.281 0.188,0.156 10 false *1 0.146,0.083 0.333,0.25 0.188,0.167 10 false *a
*1 Ohmmeter
*a Component without harness connected
(Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 12.0 Ω


If the result is not as specified, replace the fuel injector assembly.


b.

Inspect the fuel injector injection.

CAUTION:

Keep the fuel injector assembly away from sparks during the test.


i.
A264971C09
0.5,1.656 0.729,1.885 0.729,1.885 0.833,1.885 false 0.854,0.896 1.146,0.604 1.146,0.604 1.26,0.604 false 1.99,1.292 2.292,1.594 2.292,1.594 2.417,1.594 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.875,1.802 1.156,2.042 0.281,0.24 10 *a 1.323,0.51 1.646,0.771 0.323,0.26 10 *b 2.479,1.51 2.802,1.76 0.323,0.25 10 *c 3.135,0.292 3.354,0.542 0.219,0.25 10 *d
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Tube Sub-assembly


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel tube sub-assembly.

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.
A305602C03
0.906,0.135 1.333,0.135 false 1.74,0.323 2.167,0.323 false 0.865,0.75 1.292,0.75 false 2.385,1.104 2.813,1.104 false 0.906,1.031 1.333,1.031 false 0.896,1.969 1.323,1.969 false 0.729,0.938 1.042,1.094 0.313,0.156 10 false *1 0.729,0.052 1.042,0.208 0.313,0.156 10 false *a 2.25,0.25 2.563,0.406 0.313,0.156 10 false *b 0.677,0.656 0.99,0.813 0.313,0.156 10 false *c 2.896,1.031 3.208,1.188 0.313,0.156 10 false *d 0.719,1.885 1.031,2.042 0.313,0.156 10 false *e
*1 O-ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)
*e Vinyl Tube


Install a new O-ring to the fuel injector assembly.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)


iii.

Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).


iv.
A264974C27
1.938,0.427 2.375,0.427 false 2.125,1.521 2.563,1.521 false 0.865,0.417 1.302,0.417 false 2.417,0.344 2.729,0.5 0.313,0.156 10 false *a 0.688,0.344 0.833,0.521 0.146,0.177 10 false *b 2.615,1.438 2.813,1.604 0.198,0.167 10 false *c
*a SST (Adapter)
*b SST (Tie Band)
*c SST (Clamp)


Tie SST (clamp and adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41800)


v.

Install a vinyl tube onto the fuel injector assembly.

CAUTION:

Install a suitable vinyl tube onto the fuel injector assembly to prevent fuel from spraying.



vi.

Put the fuel injector assembly into a graduated cylinder.



viii.
A264973C09
2.01,0.542 2.01,0.958 false 1.948,1.01 2.219,1.292 0.271,0.281 10 *a 1.052,1.365 1.385,1.635 0.333,0.271 10 *b
*a SST (Wire)
*b Connect


Connect SST (wire) to the fuel injector assembly and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30080  

NOTICE:

Always switch the voltage on and off at the battery side, not the fuel injector assembly side.


Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - Negative (-) battery terminal Per 15 seconds 46 cc (2.8 cu. in.)


Difference between each fuel injector assembly:

13 cc (0.8 cu.in.) or less


If the result is not as specified, replace the fuel injector assembly.



c.

Check for fuel leaks.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leaks from the fuel injector assembly.

Standard fuel drop:

1 drop or less per 12 minutes


If the result is not as specified, replace the fuel injector assembly.