Home › Engine / Hybrid System › 2NR-VE FUEL › FUEL SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042276 2NR-VE FUEL _0196203 FUEL SYSTEM G

2NR-VE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Disconnect the No. 1 integration relay.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>REMOVAL


ii.
A364927C01
0.438,0.188 0.917,0.417 0.479,0.229 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.594,0.219 0.906,0.417 0.313,0.198 10 false 1D
*a Component with harness connected
(No. 1 Integration Relay)


Using a service wire, connect terminals 1D-11 and 1D-5 of the No. 1 integration relay.

NOTICE:

Be sure not to connect the wrong terminals. It may cause a malfunction.



iii.

Turn the ignition switch to ON, and check that the fuel pump operates.

NOTICE:

Do not start the engine.




b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Hide 2.INSPECT FUEL PRESSURE

a.

Take precautions to prevent gasoline spillage.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard voltage:

11 to 14 V



c.

Disconnect the cable from the negative battery terminal.


d.

Remove the air cleaner assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>THROTTLE BODY>REMOVAL


e.

Remove the EFI fuel pipe clamp.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>REMOVAL


f.

Disconnect the fuel tube sub-assembly from the fuel delivery pipe.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>REMOVAL


g.
A255967C07
2.813,0.438 2.594,0.229 2.594,0.229 2.458,0.229 false 1.677,1.635 2.083,1.219 2.083,1.219 2.177,1.219 false 0.771,2.365 0.771,2.552 false 1.5,0.802 1.5,1.063 false 0.823,0.521 0.625,0.521 false 1.063,1.031 1.063,1.198 false 1.594,3.333 1.74,3.073 1.74,3.073 1.833,3.073 false 1.302,3.979 1.396,4.073 1.396,4.073 1.51,4.073 false 2.281,3.583 2.281,3.844 false 2.719,3.333 2.719,3.635 false 2.281,0.177 2.646,0.417 0.365,0.24 10 *c 2.25,1.146 2.604,1.344 0.354,0.198 10 *d 0.708,2.583 1.052,2.792 0.344,0.208 10 *1 1,1.219 1.313,1.438 0.313,0.219 10 *b 0.458,0.469 0.865,0.698 0.406,0.229 10 *a 1.427,1.094 1.792,1.292 0.365,0.198 10 *a 2.229,3.885 2.552,4.073 0.323,0.188 10 *f 1.896,2.99 2.26,3.198 0.365,0.208 10 *a 1.573,4 1.906,4.198 0.333,0.198 10 *e 2.667,3.656 2.99,3.844 0.323,0.188 10 *g
*1 Fuel Tube Sub-assembly
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Delivery Pipe


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


h.

Wipe off any spilt gasoline.


i.

Connect the cable to the negative battery terminal.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)



k.

Measure the fuel pressure.

Standard fuel pressure:

319 to 329 kPa (3.3 to 3.4 kgf/cm2, 46 to 48 psi)


·

If the fuel pressure is greater than the standard, replace the fuel pressure regulator assembly.

·

If the fuel pressure is less than the standard, check the fuel hoses and connections, fuel pump,fuel filter and fuel pressure regulator assembly.



l.

Turn the ignition switch off.


m.

n.

Start the engine.


o.

Measure the fuel pressure at idle.

Standard fuel pressure:

319 to 329 kPa (3.3 to 3.4 kgf/cm2, 46 to 48 psi)


HINT:

Standard idle speed

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION



p.

Stop the engine.


q.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 to 329 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


r.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.


s.

Connect the fuel tube sub-assembly to the fuel delivery pipe.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSTALLATION


t.

Install the EFI fuel pipe clamp.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSTALLATION


u.

v.