77740
1.INSPECT CHARCOAL CANISTER ASSEMBLY (for Fuel Tank Cap Method)
Inspect evaporative emission control system.
Click hereEngine / Hybrid System>1NR-VE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Check for clogs in the air filter (when not using GTS or Techstream).
Start the engine.
Warm up the engine.
Allow the engine to idle after the engine has warmed up.
After 15 minutes, open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.
Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.
Open the fuel tank cap assembly again and check for inhalation sounds.
No whooshing sounds (inhalation sounds) are heard.
If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.
Check for clogs in the air filter (when using the GTS or Techstream).
Connect the GTS or Techstream to the DLC3.
Start the engine.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Active Test / Purge VSV.
Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.
Perform the "Purge VSV" Active Test while the engine is idling.
Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.
Open the fuel tank cap assembly again and check for inhalation sounds.
No whooshing sounds (inhalation sounds) are heard.
If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.
77740
2.INSPECT CHARCOAL CANISTER ASSEMBLY (for Vacuum Measurement Method)
Visually check the charcoal canister for airtightness.
Visually check the charcoal canister for cracks or damage, and check that there is no gasoline smell.
Inspect the check valve.
Disconnect the fuel emission hose.
| *a | Port A |
| *b | Air |
Apply the compressed air from the port A.
Air enters the canister through port A.
| *a | Port A |
| *b | Vacuum Pump |
Apply a vacuum from the port A, using a vacuum pump.
The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the vacuum decreases after the vacuum reaches the specified level.
Inspect evaporative emission control system
Click hereEngine / Hybrid System>1NR-VE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
| *A | for LHD |
| *B | for RHD |
| *1 | Fuel Emission Hose |
| *a | 3-way Connector |
| *b | Hose |
| *c | Vacuum Pump |
Check for clogs in the air filter (when not using GTS or Techstream).
As shown in the illustration, connect the fuel emission hose to the canister via the 3-way connector, hose and vacuum pump.
Start the engine.
Warm up the engine.
Allow the engine to idle after the engine has warmed up.
After 15 minutes, check the indicator needle on the vacuum pump.
Indicator needle of vacuum pump does not rise from its initial position.
The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.
| *A | for LHD |
| *B | for RHD |
| *1 | Fuel Emission Hose |
| *a | 3-way Connector |
| *b | Hose |
| *c | Vacuum Pump |
Check for clogs in the air filter (when using the GTS or Techstream).
As shown in the illustration, connect the fuel emission hose to the canister via the 3-way connector, hose and vacuum pump.
Connect the GTS or Techstream to the DLC3.
Start the engine.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Active Test / Purge VSV.
Perform the "Purge VSV" Active Test while the engine is idling.
Check the indicator needle on the vacuum pump.
Indicator needle of vacuum pump does not rise from its initial position.
The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.