Use the same procedure for the RHD and LHD vehicles.
68131
1.CLEAN BACK DOOR GLASS SUB-ASSEMBLY
Using a scraper, remove any excess or protruding adhesive sticking to the back door glass sub-assembly.
Be careful not to damage the glass.
Clean the outer surface of the back door glass sub-assembly with a non-residue solvent.
Even if using a new back door glass sub-assembly, clean the back door glass sub-assembly with a non-residue solvent.
64828
2.INSTALL BACK WINDOW GLASS CLIP LH
Apply primer G to the installation part of the back window glass clip LH.
Do not apply too much primer G.
Install new back window glass clip LH onto the back door glass sub-assembly, as shown in the illustration.
Allow the primer G to dry for 3 minutes or more.
64827A
3.INSTALL BACK WINDOW GLASS CLIP RH
Apply primer G to the installation part of the back window glass clip RH.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Install new back window glass clip RH onto the back door glass sub-assembly, as shown in the illustration.
64818B
4.INSTALL BACK DOOR GLASS SPACER
Apply primer M to the installation part of the back window glass spacer.
Do not apply too much primer M.
Install new quarter window glass spacer onto the back door panel sub-assembly, as shown in the illustration.
|
Back Window Glass Spacer | - | - |
| Area | Dimension |
|---|---|
| a | 2.5 mm (0.0981 in.) |
Allow the primer M to dry for 3 minutes or more.
68131
5.INSTALL BACK DOOR GLASS SUB-ASSEMBLY
|
Adhesive |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Leave as much adhesive on the vehicle body as possible.
Clean the outer edge of the back door glass sub-assembly with a non-residue solvent.
| *a | NG |
| *b | OK |
|
Primer M |
|
Adhesive |
Using a brush, apply primer M to the exposed part of the vehicle body.
Do not apply primer M to the adhesive.
Throw away any leftover primer M.
Do not apply too much primer M.
Using a brush, apply primer G to the contact surface.
| *a | Back Side | - | - |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 15.0 mm (0.590 in.) |
| b | 23.0 mm (0.905 in.) |
| c | 24.5 mm (0.964 in.) |
| d | 28.5 mm (1.122 in.) |
| e | 32.5 mm (1.279 in.) |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Cut off the tip of the cartridge nozzle as shown in the illustration.
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass sub-assembly as shown in the illustration.
| *1 | Sealer Gun | - | - |
| *a | Back Side | *b | Adhesive Center Line |
|
Adhesive | - | - |
| Area | Dimension |
|---|---|
| a | 7.0 mm (0.275 in.) |
| b | 12.0 mm (0.472 in.) |
| c | 17.0 mm (0.669 in.) |
| d | 21.0 mm (0.826 in.) |
Install the back door glass sub-assembly.
Using suction cups, position the back door glass sub-assembly so that the matchmarks are aligned. Press it in gently along the rim.
Check that the stoppers are attached to the vehicle body correctly.
Check that the vehicle body and back door glass sub-assembly have a small gap between them.
Gently press the front surface of the back door glass sub-assembly to ensure that the back door glass is securely fitted to the vehicle body.
Hold the back door glass sub-assembly in place securely with protective tape or equivalent until the adhesive hardens.
| *1 | Adhesive |
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until applied adhesive becomes hard.
Connect the 2 connectors. (w/ Rear Defogger)
6.INSTALL REAR WIPER ARM AND BLADE (w/ Rear Wiper)
76871
7.INSTALL REAR SPOILER (w/ Rear Spoiler)