Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015247 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the rear LH side manual up/down function does not operate, a malfunction may exist in the power window regulator motor assembly LH (for rear side), power window regulator switch assembly (for rear LH side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

E322676E05
1.167,1.167 1.479,1.365 0.313,0.198 10 false UP 0.917,2.385 1.531,2.583 0.615,0.198 10 false DOWN 1.677,0.885 2.135,1.083 0.458,0.198 10 false RLU+ 1.667,2.417 2.125,2.615 0.458,0.198 10 false RLD+ 1.917,3.302 2.073,3.5 0.156,0.198 10 false E 0.281,3.979 0.844,4.417 0.563,0.438 10 false F9*1 0.281,4.156 2.302,4.802 2.021,0.646 10 false Power Window Regulator Master Switch Assembly 2.167,0.885 2.479,1.083 0.313,0.198 10 false 8 2.188,2.417 2.5,2.615 0.313,0.198 10 false 9 2.177,3.292 2.49,3.49 0.313,0.198 10 false 3 3.021,0.865 3.333,1.063 0.313,0.198 10 false 1 3.021,1.635 3.333,1.833 0.313,0.198 10 false 3 3.021,2.427 3.333,2.625 0.313,0.198 10 false 5 3.521,1.469 3.833,1.667 0.313,0.198 10 false UP 3.302,2.083 3.917,2.281 0.615,0.198 10 false DOWN 3.25,0.896 3.708,1.094 0.458,0.198 10 false U+ 3.25,1.635 3.406,1.833 0.156,0.198 10 false B 3.25,2.417 3.708,2.615 0.458,0.198 10 false D+ 2.875,3.479 3.281,3.792 0.406,0.313 10 false I3 2.865,3.656 4.885,4.344 2.021,0.688 10 false Power Window Regulator Switch Assembly (for Rear LH Side) 4,1.167 4.615,1.365 0.615,0.198 10 false M/U+ 3.969,2.083 4.583,2.281 0.615,0.198 10 false M/D+ 4.438,1.167 4.75,1.365 0.313,0.198 10 false 2 4.438,2.083 4.75,2.281 0.313,0.198 10 false 4 4.771,2.083 5.083,2.281 0.313,0.198 10 false 2 6.167,2.083 6.479,2.281 0.313,0.198 10 false 1 4.719,2.667 5.146,2.958 0.427,0.292 10 false I2 4.708,2.833 6.667,3.375 1.958,0.542 10 false Power Window Regulator Motor Assembly LH (for Rear Side) 3.938,0.458 4.708,0.656 0.771,0.198 10 false POWER 5.021,0.25 6.75,0.583 1.729,0.333 10 false from IG POWER Relay 5,2.052 5.313,2.25 0.313,0.198 10 false D+ 5.865,2.052 6.177,2.25 0.313,0.198 10 false U+ 0.708,3.979 1.344,4.427 0.635,0.448 10 false G9*2 5.333,4.333 6.583,4.813 1.25,0.479 10 false *2: for LHD 4.333,4.333 5.583,4.813 1.25,0.479 10 false *1: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE) (POWER SOURCE)
a.
B398804C02
1.5,0.333 1.917,0.583 0.417,0.25 1.583,1.833 1.656,1.385 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.625,0.385 1.938,0.583 0.313,0.198 10 false I3 1.5,1.885 1.656,2.083 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Power Window Regulator Switch Assembly (for Rear LH Side))


Disconnect the I3 power window regulator switch assembly (for rear LH side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I3-3 (B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE)
a.

Remove the power window regulator switch assembly (for rear LH side).

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.

Inspect the power window regulator switch assembly (for rear LH side).

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE) - POWER WINDOW REGULATOR MOTOR LH ASSEMBLY (FOR REAR SIDE))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE)

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE) - POWER WINDOW REGULATOR MOTOR LH ASSEMBLY (FOR REAR SIDE))
a.

Disconnect the I3 power window regulator switch assembly (for rear LH side) connector.


b.

Disconnect the I2 power window regulator motor assembly LH (for rear side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-2 (M/U+) - I2-1 (U+) Always Below 1 Ω
I3-4 (M/D+) - I2-2 (D+) Always Below 1 Ω
I3-2 (M/U+) or I2-1 (U+) - Body ground Always 10 kΩ or higher
I3-4 (M/D+) or I2-2 (D+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR REAR SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR REAR SIDE)
a.

Remove the power window regulator motor assembly LH (for rear side).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


b.

Inspect the power window regulator motor assembly LH (for rear side).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE))

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR REAR SIDE)

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH SIDE))
a.

Disconnect the F9*1 or G9*2 power window regulator master switch assembly connector.

*1: for RHD

*2: for LHD



b.

Disconnect the I3 power window regulator switch assembly (for rear LH side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F9-8 (RLU+) - I3-1 (U+) Always Below 1 Ω
F9-9 (RLD+) - I3-5 (D+) Always Below 1 Ω
F9-8 (RLU+) or I3-1 (U+) - Body ground Always 10 kΩ or higher
F9-9 (RLD+) or I3-5 (D+) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
G9-8 (RLU+) - I3-1 (U+) Always Below 1 Ω
G9-9 (RLD+) - I3-5 (D+) Always Below 1 Ω
G9-8 (RLU+) or I3-1 (U+) - Body ground Always 10 kΩ or higher
G9-9 (RLD+) or I3-5 (D+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR