Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015247 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window RH does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the rear RH door manual up/down function does not operate, a malfunction may exist in the power window regulator motor assembly RH (for rear side), power window regulator switch assembly (for rear RH side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

E322676E04
1.167,1.219 1.479,1.417 0.313,0.198 10 false UP 0.917,2.385 1.531,2.583 0.615,0.198 10 false DOWN 1.646,0.833 2.104,1.031 0.458,0.198 10 false RRU+ 1.646,2.417 2.104,2.615 0.458,0.198 10 false RRD+ 1.927,3.323 2.083,3.521 0.156,0.198 10 false E 0.271,3.969 2.271,4.813 2,0.844 10 false F9*1 0.26,4.135 2.281,4.813 2.021,0.677 10 false Power Window Regulator Master Switch Assembly 2.167,0.833 2.479,1.031 0.313,0.198 10 false 1 2.167,2.417 2.479,2.615 0.313,0.198 10 false 2 2.135,3.313 2.448,3.51 0.313,0.198 10 false 3 3.021,0.885 3.333,1.083 0.313,0.198 10 false 1 3.021,1.635 3.333,1.833 0.313,0.198 10 false 3 3.021,2.417 3.333,2.615 0.313,0.198 10 false 5 3.521,1.469 3.833,1.667 0.313,0.198 10 false UP 3.302,2.083 3.917,2.281 0.615,0.198 10 false DOWN 3.25,0.896 3.708,1.094 0.458,0.198 10 false U+ 3.25,1.635 3.406,1.833 0.156,0.198 10 false B 3.25,2.417 3.708,2.615 0.458,0.198 10 false D+ 2.875,3.458 4.188,4.323 1.313,0.865 10 false H3 2.865,3.615 4.875,4.323 2.01,0.708 10 false Power Window Regulator Switch Assembly (for Rear RH Side) 4,1.167 4.615,1.365 0.615,0.198 10 false M/U+ 4,2.094 4.615,2.292 0.615,0.198 10 false M/D+ 4.438,1.167 5.063,1.76 0.625,0.594 10 false 2 4.438,2.083 4.948,2.5 0.51,0.417 10 false 4 4.823,2.083 5.542,2.656 0.719,0.573 10 false 2 6.115,2.073 7.031,2.74 0.917,0.667 10 false 1 4.75,2.635 5.063,2.833 0.313,0.198 10 false H2 4.74,2.813 6.698,4.031 1.958,1.219 10 false Power Window Regulator Motor Assembly RH (for Rear Side) 3.927,0.458 4.885,0.896 0.958,0.438 10 false POWER 5,0.25 6.688,0.792 1.688,0.542 10 false from IG POWER Relay 5,2.052 5.906,2.323 0.906,0.271 10 false D+ 5.854,2.052 6.396,2.333 0.542,0.281 10 false U+ 0.656,3.969 2.281,4.521 1.625,0.552 10 false G9*2 4.938,4.448 5.729,4.813 0.792,0.365 10 false *1: for RHD 5.979,4.448 6.771,4.813 0.792,0.365 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE) (POWER SOURCE)
a.
B398804C03
1.5,0.333 1.917,0.583 0.417,0.25 1.583,1.833 1.656,1.385 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.625,0.385 1.938,0.583 0.313,0.198 10 false H3 1.5,1.885 1.656,2.083 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Power Window Regulator Switch (for Rear RH Side))


Disconnect the H3 power window regulator switch assembly (for rear RH side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H3-3 (B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE)
a.

Remove the power window regulator switch assembly (for rear RH side).

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.

Inspect the power window regulator switch assembly (for rear RH side).

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE) - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR SIDE))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE)

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE) - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR SIDE))
a.

Disconnect the H3 power window regulator switch assembly (for rear RH side) connector.


b.

Disconnect the H2 power window regulator motor assembly RH (for rear side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-2 (M/U+) - H2-1 (U+) Always Below 1 Ω
H3-4 (M/D+) - H2-2 (D+) Always Below 1 Ω
H3-2 (M/U+) or H2-1 (U+) - Body ground Always 10 kΩ or higher
H3-4 (M/D+) or H2-2 (D+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR SIDE)
a.

Remove the power window regulator motor assembly RH (for rear side).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


b.

Inspect the power window regulator motor assembly RH (for rear side).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE))

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR SIDE)

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH SIDE))
a.

Disconnect the F9*1 or G9*2 power window regulator master switch assembly connector.

*1: for RHD

*2: for LHD



b.

Disconnect the H3 power window regulator switch assembly (for rear RH side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F9-1 (RRU+) - H3-1 (U+) Always Below 1 Ω
F9-2 (RRD+) - H3-5 (D+) Always Below 1 Ω
F9-1 (RRU+) or H3-1 (U+) - Body ground Always 10 kΩ or higher
F9-2 (RRD+) or H3-5 (D+) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
G9-1 (RRU+) - H3-1 (U+) Always Below 1 Ω
G9-2 (RRD+) - H3-5 (D+) Always Below 1 Ω
G9-1 (RRU+) or H3-1 (U+) - Body ground Always 10 kΩ or higher
G9-2 (RRD+) or H3-5 (D+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR