Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector are properly connected to the combination meter assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C253599C24
1.469,0.417 1.885,0.667 0.417,0.25 1.281,1.313 1.281,0.313 1.281,0.313 1.115,0.313 true 0.823,1.313 0.823,0.813 0.823,0.813 0.656,0.813 true 1.052,1.302 1.052,0.552 1.052,0.552 0.885,0.552 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.563,0.458 1.927,0.677 0.365,0.219 10 false E34 0.719,0.469 1.031,0.625 0.313,0.156 10 false IG 0.438,0.719 0.771,0.958 0.333,0.24 10 false +B 0.99,0.24 1.302,0.396 0.313,0.156 10 false E
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the connector from the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E34-5 (IG) - Body ground Ignition switch ON 11 to 14 V
E34-3 (+B) - Body ground Always 11 to 14 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-7 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag ECU assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to on (IG).



Result:
Proceed to
OK
NG



OK

NG