Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals ECUT and E of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag ECU assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C332665E02
0.073,0.854 2.219,1.052 2.146,0.198 10 false from IG1 Relay 1.635,1.031 2.323,1.313 0.688,0.281 10 false ECU IG1 5.844,0.76 6.156,0.948 0.313,0.188 10 false 10 6.135,0.896 6.604,1.146 0.469,0.25 10 false IG1 1.635,2.24 2.323,2.521 0.688,0.281 10 false ECU IG2 2.927,1.969 3.24,2.156 0.313,0.188 10 false 5 3.156,2.083 3.625,2.333 0.469,0.25 10 false IG 2.938,2.563 3.25,2.75 0.313,0.188 10 false 3 3.146,2.667 3.615,2.917 0.469,0.25 10 false +B 0.24,2.656 1.219,2.917 0.979,0.26 10 false from Battery 1.583,2.854 2.563,3.115 0.979,0.26 10 false BACK UP2 2.938,4.146 3.25,4.333 0.313,0.188 10 false 7 3.156,4.281 3.469,4.469 0.313,0.188 10 false E 2.813,5.625 3.125,5.813 0.313,0.188 10 false E34 2.813,5.802 4.823,6.135 2.01,0.333 10 false Combination Meter Assembly 3.656,2.083 4.125,2.333 0.469,0.25 10 false CANL 6.125,2.083 6.594,2.333 0.469,0.25 10 false CANL 3.646,2.677 4.115,2.927 0.469,0.25 10 false CANH 6.125,2.688 6.594,2.938 0.469,0.25 10 false CANH 4.135,1.948 4.448,2.135 0.313,0.188 10 false 8 4.146,2.531 4.458,2.719 0.313,0.188 10 false 9 5.813,1.938 6.125,2.125 0.313,0.188 10 false 25 5.813,2.531 6.125,2.719 0.313,0.188 10 false 26 5.854,4.167 6.167,4.354 0.313,0.188 10 false 16 6.135,4.292 6.448,4.479 0.313,0.188 10 false E1 5.656,5.635 5.969,5.823 0.313,0.188 10 false E76 5.656,5.792 7.146,6.135 1.49,0.344 10 false Airbag ECU Assembly 0.49,6.365 2.354,6.698 1.865,0.333 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Proceed to
DTCs are output
DTC is not output




DTCs are output

DTC is not output

2.CHECK BATTERY
2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and combination meter assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

4.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C332435C02
0.135,1.083 0.552,1.333 0.417,0.25 1.417,1.021 2.167,1.875 2.167,1.875 2.323,1.875 true 0.958,1.198 0.583,1.875 0.583,1.875 0.375,1.875 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.219,1.125 0.625,1.354 0.406,0.229 10 false E76 0.177,1.802 0.583,2.031 0.406,0.229 10 false E1 2.365,1.802 2.771,2.031 0.406,0.229 10 false IG1
*a Rear view of wire harness connector
(to Airbag ECU Assembly)


Disconnect the connectors from the airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E76-10 (IG1) - Body ground Ignition switch ON 8 to 16 V
E76-10 (IG1) - Body ground Ignition switch OFF Below 1 V



f.

Turn the ignition switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E76-16 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C253599C24
1.469,0.417 1.885,0.667 0.417,0.25 1.281,1.313 1.281,0.313 1.281,0.313 1.115,0.313 true 0.823,1.313 0.823,0.813 0.823,0.813 0.656,0.813 true 1.052,1.302 1.052,0.552 1.052,0.552 0.885,0.552 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.563,0.458 1.927,0.677 0.365,0.219 10 false E34 0.719,0.469 1.031,0.625 0.313,0.156 10 false IG 0.438,0.719 0.771,0.958 0.333,0.24 10 false +B 0.99,0.24 1.302,0.396 0.313,0.156 10 false E
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the connector from the combination meter assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E34-5 (IG) - Body ground Ignition switch ON 11 to 14 V
E34-3 (+B) - Body ground Always 11 to 14 V



f.

Turn the ignition switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-7 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE COMBINATION METER ASSEMBLY
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


c.

Connect the connector to the combination meter assembly.


d.

Connect the connector to the airbag ECU assembly.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

7.Clear DTC (Present and Past DTCs)
7.Clear DTC (Present and Past DTCs)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Result:
Proceed to
NEXT




NEXT

8.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
8.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch to OFF.


b.

Turn the ignition switch to ON.


c.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG